Panasonic Toughbook CF-F8EWAZZJM Page 27 Reference Manual Download

Page: 27 / 140

Battery Power

NOTE

The battery display may not correspond to the actual remaining battery power in the cases as below. To correct the
display, perform the Battery Recalibration (

page 29

• The battery indicator remains red.
• The battery indicator lights orange and the display shows 99% for a long time (79% when Economy Mode (ECO) is

enabled).

• Low battery warning appears soon after a short time of use.

The battery display may not be the same as that of Battery Meter. This is not a malfunction.

To check the remaining battery power using the battery indicator

(When the power is off or in sleep or hibernation)

<CF-F8 Series>

Close the display and confirm that the latch is locked.

<CF-W8/CF-T8 Series>

Close the display completely.

Disconnect the AC adaptor.

Slide the power switch (A) and confirm the battery indicator (B).

Battery Indicator (B)

Remaining Battery Power

Red

0 % - 4 %

Blinking orange

5 % - 19 %

Orange

20 % - 49 %

Blinking green

50 % - 94 %

Green

95 % - 100 %

CF-F8 Series

CF-W8 Series

CF-T8 Series

Summary of Contents for Toughbook CF-F8EWAZZJM













































































































































Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands

Panasonic Toughbook CF-F8EWAZZJM, Reference Manual

Search results

Summary of Contents for Toughbook CF-F8EWAZZJM

Reviews:

Related manuals for Toughbook CF-F8EWAZZJM

Brands by name

Popular brands