Opening/Closing the Setup Menu
It is possible to open the WV-CP480 TOP menu
by holding down the SET button for 2 seconds
or more while displaying camera pictures.
At first, the menu will be displayed in English.
Move the cursor to SETUP DISABLE using the
direction buttons and press the SET button to
change it to SETUP ENABLE so that the menu
becomes operable in selecting your language
and other parameters.
On the menu, you can check current settings
and perform settings to meet requirements.
To close the menu and return to camera picture, move the cursor to END and press the SET
button. (When no operation is performed for 5 minutes, the menu will automatically close.)
How to Set Up on the Menu
Operate the direction buttons (U: Up, D: Down,
L: Left, R: Right) and the SET button as shown
in the table below.
In the following pages, abbreviated expressions
will be used many times for convenience.
An abbreviated expression "Select CAMERA
and press SET" means "Move the cursor to
CAMERA by using the Up or Down button
and press the SET button." Buttons of LEFT,
UP, RIGHT, and DOWN are abbreviated as
L, U, R, and D respectively.
Function/Button
Up(U)
Down (D) Right (R)
Left (L)
Set(SET)
Open the menu
NA
NA
NA
NA
Press 2 seconds
Move the cursor
↑
↓
→
←
NA
Select a setup item
↑
↓
NA
NA
NA
Select a parameter
NA
NA
→
←
NA
Apply settings
NA
NA
NA
NA
Press
Open a sub-menu
(Move the cursor to the item with
↓
.)
Press
Close the menu
(Move the cursor to END.)
Press
Return to the previous menu
(Move the cursor to RET.)
Press
Return to the top menu
(Move the cursor to TOP.)
Press
Reset a specific item
(Move the cursor to the item to be reset , press L and R simultaneously.)
Reset all*
1
(When camera picture is displayed, press L, R and SET simultane-
ously for 2 seconds.)
Enable/Disable the menu *
2
(Move the cursor to SETUP DISABLE/ENABLE, press SET)
Scroll up or down the page
(Hold down
↑
or
↓
)
Notes:
• NA: Not Applicable.
• *1 "Reset all" is an irrevocable procedure that resets all settings to the default values.
The PIX OFF setting will not be reset. We recommend that you take note of settings
before executing this command (except the PIX OFF settings).
• *2
Before operating the menu, change SETUP DISABLE (default setting) to
SETUP ENABLE.
• When closing the menu, the changed settings will be stored in the memory of the
camera and will remain until the settings are overwritten by new ones.
• Use a system controller to operate setup menus after installation as necessary. Almost
all operations will be available unless otherwise mentioned.
Top Menu and Sub Menus
The following menus will be displayed in the language selected on the LANGUAGE SETUP
menu.
There are four sub menus selectable on the top menu: CAMERA SETUP (2 pages), BACK-
FOCUS SETUP, SPECIAL SETUP, and LANGUAGE SETUP. On these menus, select a setup
item followed by "
↓
" and press the SET button to open more sub menus.
ABOUT SETUP MENUS
MODEL WV-CP480 SERIES
CAMERA
BACK-FOCUS
SPECIAL
LANGUAGE
END SETUP DISABLE
↵
↵
↵
↵
(UP)
(LEFT)
(RIGHT)
(DOWN)
(SET)
NEAR
FAR
ABF/MENU
Up Button
Right Button
Down Button
Left Button
Set Button
SETUP DISABLE
SETUP ENABLE
**CAMERA SETUP** 2/2
PRIVACY ZONE OFF
MIRROR OFF
LENS-DRIVE DC
STABILIZER OFF
RET TOP END
**LANGUAGE SETUP**
LANGUAGE ENGLISH
SET
RET TOP END
MODEL WV-CP480 SERIES
CAMERA
BACK-FOCUS
SPECIAL
LANGUAGE
END SETUP ENABLE
↵
↵
↵
↵
**SPECIAL SETUP**
CHROMA GAIN .....I...
AP GAIN ...I.....
PEDESTAL .....I...
HUE ....I....
- +
PIX OFF
COMMUNICATION COAX
CAMERA RESET
→
PUSH SW
SER.NO. XXXXXXXX
RET TOP END
↵
**BACK-FOCUS SETUP**
ABF
→
PUSH SW
MANUAL-ADJ
C/L
← →
B/W AUTO
SETUP-SW LOCK OFF
NEAR FAR
.........I..........
INDICATOR 9999
RET TOP END
↵
**CAMERA SETUP** 1/2
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON(HIGH)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
DNR HIGH
RESOLUTION HIGH
BW MODE
↵
↵
↵
↵
