8
8
Control of 2WAY SYSTEM
2. Wireless Remote Controller
Before requesting service, please check the followings.
e
s
u
a
C
m
e
l
b
o
r
P
Solution
The unit doesn’t work even
when
is pressed on the
remote controller.
The power to the indoor unit is not ON.
Make sure the power to the indoor unit is ON.
Are the remote controller’s batteries dead?
Change the batteries.
Is there a mismatch between the display lamp and
cooling/heating or is it set to something other than
Auto? (The operating lamp stays lit, while the timer
lamp and the standby lamp blink alternately.)
Change the operating mode.
Do the addresses match one another?
Check the addresses of the receiver
*1
and the
remote controller. (See Page 8-9)
The air conditioner starts and
stops on its own.
Has the timer been set to repeat?
Check the timer settings.(See Page 8-7)
“
”
is displayed on the remote
controller when the unit is
stopped.
An error has occurred in the non-volatile
memory.
Please contact your sales outlet.
Although the unit is for air conditioning only, either Auto or Heat is indicated
in the display.
Make settings to the remote controller’s operation
mode display. (See Page 8-12)
After putting the batteries in the remote controller, even when it is operated,
the display does not change.
Press the Reset button on the remote controller.
(See Page 8-5)
The timer cannot be set.
Make the settings when the remote controller is in
Operation Display. (See Page 8-7)
If the problem persists even after you check the foregoing items, stop the unit, disconnect the power to the indoor unit and
contact the dealer where the product was purchased with the model number and problem you are having.
As it is dangerous, under no circumstances should you undertake repairs yourself.
Further, when the receiver’s
*2
lamps are blinking; please contact your retailer with that information.
8-13. Before Requesting Service
Specifications
CZ-RWSU3/CZ-RWSC3/CZ-RWSK2
CZ-RWSU3/CZ-RWSC3
Wireless Remote Controller
Receiver
Dimensions
182 mm (H) X 61 mm (W) X 18.5 mm (D)
Power source
Two AAA alkaline batteries
Clock Accuracy ±30 seconds per month (at 25 °C)
Dimensions
Power source
29.7 mm (H) X 211.8 mm (W) X 211.8 mm (D)
120 mm (H) X 70 mm (W) X 20 mm (D)
16 V DC (Supplied from the terminal
strip of the indoor unit’s remote controller)
CZ-RWSC3
CZ-RWSU3
8-12. Miscellaneous Settings
A variety of changes can be made to settings, depending on the indoor unit being used.
Operation mode indicator, time display (24 hour, AM/PM), Heat Max Temp
•
(These settings are saved in nonvolatile memory in the remote controller, so even when its batteries are changed,
the settings do not have to be made again.)
•
First check the display of the remote controller when the unit is stopped and then make any desired settings.
How to Operate
•
While holding down the buttons below, every time
is pressed the remote controller’s display changes.
•
Whatever is being displayed when you release
is set.
Setting Item
Operation Button
Setting Content
Remote Controller Display
Remote controller
operation mode
display setting
when is pressed
Press
while pressing
Heat Pump
(with Auto)
Heat Pump
(without Auto)
Dedicated air
conditioner
Clock display
setting
Press
while pressing
24 Hour
AM/PM
Max possible
temperature
setting in the
Heat mode
Press
while pressing
Maximum heating
temperature range is
26 °C – 30 °C
8-12
SM830252-01_欧州_Single_8・10HP_TD_SM.indb 12
16/10/12 15:51:25
AMP Air Conditioning
www.ampair.co.uk | [email protected]
