background image

Rx450AC Rx550DC MK3 Installation Manual - V19 30Sep05.doc

Page 17/28

CABLE LENGTH COMPENSATION

 

 
The receiver incorporates a remotely adjustable high quality launch amplifier to 
compensate for video cable losses over extended cable distances. 
 
The gain of the launch amplifier can be adjusted in the receiver

 LAUNCH AMP GAIN

 line 

of the 

MAIN/RECEIVER/OPTIONS

 menu.  The gain can be varied from 0 - 255, the 

higher the number, the higher the gain.  The default value is 0.  As the amplifier gain is 
increased, high frequency lift is also increased. 

 
SELF-TEST AND DIAGNOSTIC SEQUENCE 

 

The diagnostic system and status check, which will activate each receiver function for 2-3 
seconds in turn, is activated by selecting 

SELF TEST

 from the receiver

 

MAIN/RECEIVER/TEST

 menu.  The self test can also be activated by pressing both the 

UP

 and 

DOWN

 buttons on the receiver top pcb simultaneously, allowing local self test of 

a stand alone receiver.  (Please refer to earlier diagram for button positions). 
 
The receiver OSD displays the self test progress with two status lines as shown below. 
 

FUNCTION

 

Å

 this line will show the current function being driven. 

Pxxxx Txxxx Zxxxx Fxxxx

 

Å

  

the xxxx indicate preset pot values for pan, tilt, 
zoom and focus.  Each value should change 
smoothly as the corresponding function is driven. 

 

 

Functions: Active 

output 

 

PAN LEFT 

J7/PM+/- PB+/- 

 

PAN RIGHT 

J7/PM+/- PB+/- 

 

TILT DOWN 

J7/TM+/- TB+/- 

 

TILT UP 

J7/TM+/- TB+/- 

 

ZOOM IN (Lens driven fully IN) 

J10/ZM 

 

ZOOM OUT (Lens driven fully OUT) 

J10/ZM 

 FOCUS 

NEAR 

J10/FC 

 FOCUS 

FAR 

J10/FC 

 AUX 

LAMPS 

J6/LAMPS 

 AUX 

WASHER 

J6/WASH 

 AUX 

WIPER 

J6/WIPE 

 

Diagnostic check complete, receiver 
will display a results screen and drive 
the head and lens for 5 seconds. 

 

 
During the self test, the presence and sense of each preset input is recorded. Following 
the self test the display shows if the preset inputs for pan/tilt/zoom and focus was 
detected. Also the pan/tilt head and lens outputs are driven for approx 5 seconds to 
indicate the results. If the drive led is GREEN then preset is ok and if RED then not ok. 

Summary of Contents for RX550





























Reviews: