Panasonic Real Pro Ultra EP30006 Service Manual Download Page 42 | Manualshive

Page: 42 / 76

background image

EP30006

ORDER NO.HPD0706U16C1

-

42

-

10.15.8.

Removing the Float air bag

1. Remove the Massage mechanism block from the Rear frame.

2. Remove the PCB install plate.

3. Remove the Pin.

4. Remove the Rivet.

5. Unscrew the Screw.

6. Move the Float air bag in the direction of arrows, and

remove it from the hollow parts of the Float air bag.

7. Move the Eccentric link plate in the direction of the arrows

and unhook it.

*Until the hook is released, move the Air bag in the direction of

the arrow 1.

8. Unscrew two Screws on the Float air bag.

«
...
40
41
42
43
44
...
»

Summary of Contents for Real Pro Ultra EP30006













































































Reviews:

No comments

Related manuals for Real Pro Ultra EP30006

Brand: OBH Nordica Pages: 14

Brand: Comfier Pages: 8

Brand: Minerva Pages: 8

Brand: Osaki Pages: 7

Brand: Nekteck Pages: 17

Brand: Oregon Scientific Pages: 61

Brand: Coopers of Stortford Pages: 3

Brand: KYOTA Pages: 28

Brand: Bodi-Tek Pages: 40

Brand: Infinity Pages: 12

Brand: Infinity Pages: 28

Prelude MTS Center

Brand: Infinity Pages: 32

Obus Forme HMC1

Brand: Conair Pages: 2

Brand: Conair Pages: 2

Brand: Conair Pages: 2

BodyBenefits BMS9PC

Brand: Conair Pages: 6

Brand: Conair Pages: 6

Brand: Conair Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands