Panasonic Real Pro Ultra EP30006 Service Manual Download Page 54

Page: 54 / 76

EP30006

ORDER NO.HPD0706U16C1

13.2.

CHECKING THE AIR BAGS

1. You can check the air leakage by this inspection.

Remove the Under covers.

Connect the Air inspection tool (WEP000S8908) and the

Special hose (WEP000K8917) to each Hoses from the Under

box. *Connect to the Hose that you inspect.

2. Turn the power switch on and push the On/off button on

the Controller. Open the left cover and check each

operations of LEG/FOOT, SEAT, HAND/ARM, and

SHOULDER.

3. Push the button of Air intensity on the Controller and check

the 5-level pressures. If the values are within the

standard, the Air bags, Pump unit, and Air hoses are normal. If not, the following malfunctions are assumed:

1.Bent hoses between Air bags and Pump unit

2.Malfunction of each Electromagnetic valves

3.Malfunction of Pump unit

4.Air bag rupture

Summary of Contents for Real Pro Ultra EP30006













































































Search results

Summary of Contents for Real Pro Ultra EP30006

Reviews:

Related manuals for Real Pro Ultra EP30006

Brands by name

Popular brands

Panasonic Real Pro Ultra EP30006, Service Manual

Search results

Summary of Contents for Real Pro Ultra EP30006

Reviews:

Related manuals for Real Pro Ultra EP30006

Brands by name

Popular brands