background image

ORDER NO. HPD0906U07P1 

 

 

 

 

Model No.

 

EP30006/EP30005/EP30004       EP30003 

Please revise the original parts list in the Service Manual to conform to the change(s) shown herein. 
If new part numbers are shown, be sure to use them when ordering parts. 

Reason for Change 

*The circled item indicates the reason.    If no marking, see the Notes in the bottom column.

 

1. Improve 

performance 

 

2. 

Change of material or dimension 

 

3. 

To meet approved specification 

 

4. Standardization 

 

5. Addition 

 

6. Deletion 

 

7. 

Correction 

 

8. Other 

 

Interchangeability Code 

**The circled item indicates the interchangeability.    If no marking, see the Notes in the bottom column.

 

 Parts 

 

Set 

Production 

 

Original   Early 

New  

Late 

Original or new parts may be used in early or late production set. 
Use original parts until exhausted, then stock new parts. 

Original   Early 

New  

Late 

Original parts may be used in early production sets only.  New parts may be used in early or late 
production sets.    Use original parts where possible, then stock new parts. 

Original   Early 

New  

Late 

New parts only may be used in early or late production sets. 
Stock new parts. 

Original   Early 

New  

Late 

Original parts may be used in early production sets only.    New parts may be used in late production 
sets only.    Stock both original and new parts. 

E Other 

 

 

Only

 

replacement

 

part

 

number

 

is

 

changed. 

Part Number

 

Model No. 

Ref. No. 

Original Part No. 

New Part No. 

Notes(*

,

**) 

Part Name & Descriptions 

Remarks 

EP30006/EP300

05/EP30004 

171 WEP3530K3698 

 

WEP3530K3648 

8*

C** 

ARMREST RIGHT 

 

 172 

WEP3530K3708 

WEP3530K3718 

8*

C** 

ARMREST LEFT 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EP30003 171 

WEP3510K3698 

 

WEP3510K3648 

8*

C** 

ARMREST RIGHT 

 

 172 

WEP3510K3708 

WEP3510K3788 

8*

C** 

ARMREST LEFT 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

File this Parts Change Notice with your copy of the Service Manual. 

 

 

 

All these parts are supplied from SHPEW (China) factory.   

Summary of Contents for Real Pro Ultra EP30006













































































Reviews: