Panasonic PT-RQ22K Operating Instructions (Functional Manual) Download Page 186

Page: 186 / 288

Chapter 4

Settings — [PROJECTOR SETUP] menu

186 - ENGLISH

[SERIAL NUMBER]

Displays the serial number of the projector.

[PROJECTOR RUNTIME]

Displays the runtime of the projector.

[LIGHT RUNTIME]

Displays the runtime of the light source 1 and the light source 2.

[CONTINUOUS LIGHTING

TIME]

Displays the elapsed time from when the light source is illuminated.

The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.

The elapsed time is reset when the light source is temporarily turned off such as using the shutter

function.

[MAIN/SUB VERSION]

Displays the main and sub versions of the firmware of the projector.

[INTAKE AIR TEMP.]

Displays the status of the intake air temperature of the projector.

[OPTICS MODULE TEMP.]

Displays the status of the internal temperature of the projector.

[EXHAUST AIR TEMP.]

Displays the status of the exhaust air temperature of the projector.

[LIGHT1 TEMP.]

Displays the light source 1 temperature status of the projector.

[LIGHT2 TEMP.]

Displays the light source 2 temperature status of the projector.

[SELF TEST]

Displays the status of the projector.

[INPUT]

Displays the input terminal currently selected.

Displays the representative input terminal when one image is displayed with multiple input signals.

[SIGNAL NAME]

Displays the input signal name.

[MEMORY NO.]

Displays the memory number of the input signal.

[BACKUP INPUT STATUS]

Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT

MODE] is set to [OFF]. (

page 125)

[NUMBER OF REGISTERED

SIGNAL]

Displays the number of registered signals.

[COOLING CONDITION]

Displays the set cooling conditions.

[ATMOSPHERIC PRESSURE]

Displays the atmospheric pressure.

[REMOTE2 STATUS]

Displays the control status of the REMOTE2.

[AC VOLTAGE]

Displays the input supply voltage.

[LENS TYPE]

Displays the type name (type of the projection lens) set to the projection lens.

[LENS ID]

Displays the ID set to the projection lens.

[LENS NAME]

Displays the name set to the projection lens.

[LENS THROW RATIO]

Displays the range of throw ratio supported by the projection lens in accordance with the [LENS

TYPE] setting.

[LENS ZOOM TYPE]

Displays the drive method of the zoom motor attached to the projection lens.

[ZOOM CALIBRATION]

Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.

[ON COUNT]

[POWER ON TIMES]

Displays the number of times the power is turned on.

[MECHANICAL SHUTTER]

Displays the number of times the mechanical shutter is closed.

It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].

[OPERATING MODE]

Displays the setting value of the [PROJECTOR SETUP] menu

→

[OPERATION SETTING]

→

[OPERATING MODE].

[NORMAL]

Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].

[ECO]

Displays the runtime of the light source with [OPERATING MODE] set to [ECO].

[USER1]

Displays the runtime of the light source with [OPERATING MODE] set to [USER1].

[USER2]

Displays the runtime of the light source with [OPERATING MODE] set to [USER2].

[USER3]

Displays the runtime of the light source with [OPERATING MODE] set to [USER3].

[CONSOLIDATED RUNTIME]

Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the

time used with the [NORMAL] setting.

The converted runtime is used for a rough indication about when to perform maintenance when the

projector is used in combination of each item in [OPERATING MODE].

[UPGRADE KIT]

[ET-UK20]

Displays the activation status by the Upgrade Kit (Model No.:

ET-UK20).

[ET-CUK10]

Displays the activation status by the Auto Screen Adjustment

Upgrade Kit (Model No.: ET-CUK10).

[SLOT1]

Displays the product model number of the Interface Board installed in <SLOT 1>.

Also, the firmware version is displayed after the product model number.

[SLOT2]

Displays the product model number of the Interface Board installed in <SLOT 2>.

Also, the firmware version is displayed after the product model number.

Summary of Contents for PT-RQ22K

































































































































































































































































































Search results

Summary of Contents for PT-RQ22K

Reviews:

Brands by name

Popular brands

Panasonic PT-RQ22K, Operating Instructions (Functional Manual)

Search results

Summary of Contents for PT-RQ22K

Reviews:

Brands by name

Popular brands