Chapter 4
Settings — [DISPLAY OPTION] menu
ENGLISH - 109
[ENABLE]
Switches to the secondary input automatically when the input signal for primary input is disrupted.
[DISABLE]
Disables the automatic input switching function.
Note
f
The backup function is enabled when [BACKUP INPUT MODE] is set to anything other than [OFF] and same signal is input to the primary
input and the secondary input.
f
To switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use
the function.
g
Set [BACKUP INPUT MODE] to anything other than [OFF].
g
Input the same signal to the primary and secondary inputs.
g
Display the image of the primary input.
f
If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to use
the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input.
f
When [BACKUP INPUT MODE] is set to anything other than [OFF], the combination of that input is displayed in [PRIMARY INPUT] and
[SECONDARY INPUT] of the
[BACKUP INPUT SETTING]
screen.
f
[BACKUP INPUT STATUS] is displayed in the input guide (
x
page 132) and the
[STATUS]
screen (
x
pages 77 and 156 ) when
[BACKUP INPUT MODE] is set to anything other than [OFF].
When the signal can be switched to the backup input signal using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS].
When it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] shows [ACTIVE] while displaying the image from the primary
input.
The primary input will be the backup input when [BACKUP INPUT STATUS] shows [ACTIVE] while displaying the image from the secondary
input.
f
When [BACKUP INPUT MODE] is set to anything other than [OFF], the input is switched seamlessly if the input is switched between the
primary input and the secondary input while it is possible to switch to the backup input signal.
f
When [AUTOMATIC SWITCHING] is set to [ENABLE] and [BACKUP INPUT STATUS] shows [ACTIVE], the input is automatically switched
to the backup input when a disruption occurs in the input signal.
f
When [AUTOMATIC SWITCHING] is set to [ENABLE], the indication in [BACKUP INPUT STATUS] will change to [INACTIVE] if the input
signal is disrupted and automatically switched to the backup input. In this case, it is not possible to switch to the backup input signal until the
original input signal is restored. If the input has switched to the backup input automatically, it is possible to switch to the backup input signal
when the original signal has restored. In this case, the current input is maintained.
f
[BACKUP INPUT SETTING] cannot be set while in the four-screen display mode. The backup operation is not performed either. Set the
[MULTI DISPLAY] menu
→
[MULTI DISPLAY MODE] to anything other than [OFF] when using the four-screen display mode.
f
[BACKUP INPUT MODE] in which the standard SDI input is included as the primary input or the secondary input cannot be selected when
[SDI IN] in [SIMUL INPUT SETTING] is set to anything other than [OFF].
f
[BACKUP INPUT MODE] including the primary input or the secondary input equipped on the optional Interface Board installed in the slot
cannot be selected when [SLOT IN] in [SIMUL INPUT SETTING] is set to anything other than [OFF].
f
When [SDI LINK SETTINGS] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT MODE] for that combination
cannot be selected. When [SDI LINK SETTINGS] for the primary input and the secondary input do not match, [BACKUP INPUT MODE] for
that combination cannot be selected.
Match the following settings in accordance with the signal and then input the same signal in the primary input and the secondary input.
g
[SDI LINK] in the [DISPLAY OPTION] menu
→
[SDI IN]
g
[SDI LINK] in the [DISPLAY OPTION] menu
→
[SLOT IN]
f
When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT
MODE] for that combination cannot be selected. When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the
secondary input do not match, [BACKUP INPUT MODE] for that combination cannot be selected.
Match the setting in accordance to the signal and then input the same signal in the primary input and the secondary input.
g
[HDMI LINK] in the [DISPLAY OPTION] menu
→
[SLOT IN]
g
[DVI-D LINK] in the [DISPLAY OPTION] menu
→
[SLOT IN]
[SIMUL INPUT SETTING]
Set this function when the video signal in simultaneous format is input and used.
1) Press
as
to select [SIMUL INPUT SETTING].
2) Press the <ENTER> button.
f
The
[SIMUL INPUT SETTING]
screen is displayed.
3) Press
as
to select [SDI IN], [SLOT IN].
f
[SLOT IN] can be selected when the optional Interface Board is installed in the slot.
4) Press
qw
to switch the setting.
f
The items will switch each time you press the button.
[OFF]
This is not used for simultaneous input.
[AUTO(x2-speed)]
Displays the image in double speed using the signals input in the two input terminals.
[AUTO(x4-speed)]
*1
Displays the image in quadruple speed using the signals input in the four input terminals.
*1 [SLOT IN] cannot be set to [AUTO(x4-speed)] when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in
<SLOT 1> or <SLOT 2>.
