Chapter 5
Operations — Memory Viewer function
106 - ENGLISH
f
After playback ends, playback goes into pause state at the beginning of the file.
f
Pressing
w
during playback performs fast-forward playback. Every press of
w
increases the speed. (3
levels)
f
Pressing
q
during playback performs rewind playback. Every press of
q
increases the speed. (3 levels)
f
Pressing
a
plays back the file being played back from the beginning. (cue)
f
Pressing
w
during pause skips the file being played back and starts playback of the next file.
f
Pressing
q
during pause returns playback to the previous file and starts playback.
2) Press the <RETURN> button.
f
Full-screen display ends and the Memory Viewer screen in thumbnail view returns.
Note
f
If the number of recording pixels is less than 1 024 x 768, the image is enlarged with the aspect ratio maintained.
f
If the number of recording pixels is more than 1 024 x 768, the image is reduced with the aspect ratio maintained.
f
The playback order follows the display order set in the [MEMORY VIEWER] menu
→
[SORT] (
x
page 69).
Also in the cases where still image and movie files both exist in the same folder, they are played back according to the [SORT] setting.
f
The time bar of the operation guide on the lower part of the playback screen can be hidden by setting the [MEMORY VIEWER] menu
→
[GUIDE] (
x
page 70) to [OFF].
f
When images cannot be played, an error message is displayed.
f
When switching the input to [MEMOERY VIEWER] while [AUTOPLAY] is set to [ON], automatic playback starts.
Resume playback
When automatic playback is disabled (the [MEMORY VIEWER] menu
→
[AUTOPLAY] (
x
page 69) is set to
[OFF]), resume playback can be performed.
Resume playback is a function that stops movie playback in the middle and restarts playback from the position
where the movie has been stopped the last time when the same file is to be played back next time.
The following operations resume playback from the position where the last playback has been stopped.
f
Stopping movie playback in the middle, going back to the Memory Viewer screen, and then selecting the same
movie file again and playing it back
f
After playing back other movie or still image files, selecting the previous movie file and playing it back.
Note
f
Resume information (information on the position when movie playback is stopped in the middle) is automatically saved at the time when
playback is paused by pressing the <ENTER> button during playback or when full-screen display is ended by pressing the <RETURN>
button during playback.
f
Resume information (information on the position when movie playback is stopped in the middle) of 50 movie files can be saved. After the
51st movie file is played back, resume information will be deleted in order from the oldest.
f
When resume playback is performed, some files may not be played back from the correct position where the last playback has been
stopped.
f
All resume information are deleted if switching the input to other than MIRRORING, removing the SD card, setting to standby status while
the [SETUP] menu
→
[ECO MANAGEMENT]
→
[STANDBY MODE] (
x
page 76) is set to [ECO] or [NETWORK], the turning off the power
supply of the track system.
Playing back still images/movies automatically when the projector is turned on
When the following three conditions are met, playback of still images/movies starts automatically when the
projector is turned on.
f
Automatic playback is enabled
g
The [MEMORY VIEWER] menu
→
[AUTOPLAY] (
x
page 69) is set to [ON]
f
The input is set to Memory Viewer when the power is turned on to start projection
g
The [SETUP] menu
→
[STARTUP INPUT SELECT] (
x
page 77) is set to [MEMORY VIEWER]
g
The [SETUP] menu
→
[STARTUP INPUT SELECT] (
x
page 77) is set to [LAST USED], and the power is
turned off with the input set to Memory Viewer
f
There are still image/movie files that can be played back with the Memory Viewer function in the root folder of
the SD card
Note
f
The playback order follows the display order set in the [MEMORY VIEWER] menu
→
[SORT] (
x
page 69).
Also in the cases where still image and movie files both exist in the same folder, they are played back according to the [SORT] setting.
f
To play back still image/movie files automatically when the power supply of the track system is turned on, perform the following setting and
operation.
g
Set the [SETUP] menu
→
[INITIAL STARTUP] (
x
page 77) to [ON]
g
Set the [SETUP] menu
→
[INITIAL STARTUP] (
x
page 77) to [LAST MEMORY], and turn off the power supply of the track system
while projecting
