background image

4 - ENGLISH

CAUTION

Do not install this product in a location where salt damage occurs or corrosive gas is generated.

Doing so may cause falling due to corrosion.

Do not put excessive force on the projector by hanging on the projector or dangling any object.

Doing so may result in falling of the projector and injuries.

Mount this product according to the specified orientation.

Mounting this product to the floor or in an improper orientation may result in tumbling or the falling of projector.

When disconnecting the power cord, be sure to hold the power plug (the outlet side) and the power 

connector (the projector side) and pull it off. 

If the power cord itself is pulled, the lead may become damaged, and fire, short-circuits or serious electric 

shocks may result.

Read this first! (continued)

WARNING

Do not handle the power plug and power connector with wet hands. 

Failure to observe this may result in electric shocks.

Do not use the supplied power cord with equipment other than a specified projector.

Using the supplied power cord with equipment other than a specified projector may cause electric shock or fire 

due to a short or heat generation. 

Do not allow children to reach the supplied screws and the string.

Accidentally swallowing them can cause physical harm.

 

z

If swallowed, seek medical advice immediately.

Summary of Contents for PT-JX200FBE































Reviews: