background image

24 - ENGLISH

Installation (continued)

 

r

 Install the projector to a ceiling

Shaft

Attachment plate

Projector mount bracket

Groove

Ball joint 

fixing screw

1) Changing the orientation of the main unit of 

the projector.

 

z

Refer to "Changing the orientation of the 

main unit of the projector" (

 page 19), 

adjust the orientation of the main unit of the 

projector as shown in the left illustration and 

then fasten the ball joint fixing screw.

2) Attach the groove of the projector mount 

bracket to the shaft of the attachment plate.

Warning:

The mounting and installation must be carried 

out by two or more persons.

Hook

Shaft

Groove

3) Attach the projector mount bracket to the 

attachment plate.

 

z

Slide the projector mount bracket and make 

the groove of the projector held on to the 

shaft of the attachment plate.

Attention

 

z

Do not release your hand until the 

attachment plate is fitted into both sides (the 

shaft side and the hook side) of the projector 

mount bracket.

4) Secure the projector mount bracket to 

the attachment plate with the screws and 

captive washers.

 

z

Firmly secure the projector mount bracket 

with the four supplied screws and captive 

washers (M4 x 8).

Summary of Contents for PT-JX200FBE































Reviews: