Panasonic NV-GS40, Operating Instructions Manual

Page: 54 / 76

Others
-54-
Notes and Hints
ª
Concerning the Power Supply
≥
When the Movie Camera is used for a long time,
the Camera body becomes warm, but this is not
a malfunction.
≥
If the [CHARGE] Lamp does not light up
although the Battery is attached to the AC
Adaptor, detach the Battery and reattach it.
ª
Inserting/Removing the Cassette
≥
In the case of using a previously recorded
Cassette, you can use the Camera Search
Function to find the position where you want to
continue recording.
≥
If a new Cassette is inserted, rewind to the
beginning of the tape before starting recording.
≥
When inserting the cassette, make sure it faces
in the right direction and then push it in until it
stops.
≥
When the Cassette Holder is in action, do not
touch anything except the [PUSH CLOSE]
Button.
≥
When closing the Cassette Compartment
Cover, do not get anything caught in the cover,
such as a cable of an optional stereo
microphone.
ª
Alarm Sounds
When [BEEP SOUND] on the
[OTHER FUNCTIONS1] Sub-Menu on the
[CAMERA FUNCTIONS] Main-Menu is set to
[ON], confirmation/alarm beeps are issued as
follows.
1 Beep
≥
When you start recording
≥
When you switch the [OFF/ON/MODE] Switch
from [OFF] to [ON]
2 Beeps
≥
When you pause recording
2 Beeps for 4 times
≥
If you perform a wrong operation before or
during recording
ª
Recording Check
≥
For Recording Check, the recording speed
mode (SP/LP) must be the same as the mode
used for the recording. If different, playback
images will be distorted.
ª
Camera Search
≥
In Camera Search Mode, images may contain
mosaic-pattern noise. This is a phenomenon
that is characteristic of digital video and not a
malfunction.
≥
If the recording speed modes (SP/LP) of
previous recording and new recording are
different, playback images may be distorted.
ª
Quick Start
≥
During the Quick Start Standby Mode, a minute
amount of electricity is consumed.
≥
When the Movie Camera is left in the Recording
Pause Mode for 6 minutes, it will be turned into
the Quick Start Standby Mode. To turn the
Movie Camera on again, set the
[OFF/ON/MODE] Switch to [OFF] and then set it
to [ON] again. (The Quick Start Mode will be
restored.)
≥
This Function is not activated in the following
cases even if the Quick Start Recording Lamp
lights:
≥
A tape is not inserted, while the Tape Mode
is set.
≥
A Card is not inserted, while the Card Mode
is set.
≥
In the following cases, Quick Start is temporarily
cancelled when the Quick Start Mode is set. Set
the Camera Mode again, and the Quick Start
Mode will be restored.
≥
Set to the VCR Mode or Card Playback
Mode
≥
The Battery is replaced
≥
If the [QUICK START] Button is pressed and
held for approximately 2 seconds during the
Quick Start Standby Mode, the Lamp will go off
and the Movie Camera will completely be turned
off.
≥
If the Movie Camera is not operated for
approximately 30 minutes when the Quick Start
Recording Lamp lights, the Lamp will go off and
the Movie Camera will completely be turned off.
≥
In the Automatic White Balance Mode, the
colour may be recorded unnaturally at the
beginning of the recording.
≥
The zoom magnification differs from when it is
in the Quick Start Standby Mode and when the
recording starts.
ª
Photoshot
≥
Photoshot Recording results in slightly inferior
image quality.
50B-ENG.book 54 ページ ２００３年１月１７日 金曜日 午後５時２９分