Panasonic KX-TVM200 Installation Manual Download Page 70

Page: 70 / 250

2.14 Initialising the VPS During Installation

Installation Manual

2.14 Initialising the VPS During Installation

Before programming the VPS for the first time, perform the initialisation procedure described below.
All settings are reset to their default values.

Recorded messages are erased

. System Prompts

(including customised prompts) are preserved.

Turn the power switch to the off position.

Set the Mode Switch to position 5 (see 2.3 Names and Locations).

Turn the power switch to the on position.

Confirm that the Run Indicator blinks 5 times.

•

This may take several minutes. The Alarm Indicator and Run Indicator will first blink
intermittently before the Run Indicator blinks 5 times.

Turn the power switch off at the VPS.

Set the Mode Switch to position 0.

Turn the power switch back on at the VPS.

CAUTION

If the Mode Switch is not set to position 0, all programming will be lost when the power is switched
off!

After initialising the VPS, continue with the installation procedure and/or begin programming the VPS.

Summary of Contents for KX-TVM200



























































































































































































































































Search results

Summary of Contents for KX-TVM200

Reviews:

Brands by name

Popular brands

Panasonic KX-TVM200, Installation Manual

Search results

Summary of Contents for KX-TVM200

Reviews:

Brands by name

Popular brands