manualshive.com logo in svg

Panasonic KX-TVM200, Installation Manual

Share
Download
Panasonic KX-TVM200 Installation Manual Download Page 177

5.6 KX-TD500 PBX Programming for Inband Integration

Installation Manual

177

5.6

KX-TD500 PBX Programming for Inband 
Integration

DPT Integration is recommended when using the VPS with the KX-TD500, however, Inband 
Integration is necessary when:

•

the PBX has available SLT ports but no available DPT ports.

•

the cards installed in the PBX or the software version of the PBX do not support DPT 
Integration.

Programming procedures and availability may vary by country/area, software version, etc. 
Refer to the documentation included with the PBX or consult your dealer for more information.

1.

Assignment of the extension card to be connected to the VPS

a)

Go

 to the 

"1-1 Slot Assignment"

 screen.

b)

Assign

 the slot card type to be installed to 

"DHLC", "HLC", "SLC", "ESLC",

 or 

"SLC-M"

 

SLT interface supports.

c)

Click "Apply"

 to save the slot card type assignment.

d)

Set "Card Status"

 to 

"INS".

Summary of Contents for KX-TVM200



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands