manualshive.com logo in svg

Panasonic KX-TS600CB, Operating Instructions Manual

Share
Download
Panasonic KX-TS600CB Operating Instructions Manual Download Page 44

Special Features

44

6

Press 

[OK]

 (

Save

 key).

• A long beep sounds.
• The display will return to step 3. To exit the programming mode, press 

[EXIT]

 or wait for 60 seconds.

To cancel the call restriction

Follow steps 1 through 4 on page 43. In step 5, press 

[ERASE]

 to clear the 

restricted digits, and press 

[OK]

 (

Save

 key).

Voice Mail Service

Voice mail service is an electronic on-line answering system offered by 
your telephone company. After subscribing, the voice mail system can 
answer calls automatically when your line is busy or if calls are not 
answered. Callers can leave messages by following the pre-recorded 
instructions. When voice mail messages are recorded, “

Voice mail

” and 

“

” will be displayed.

Listening to Voice Mail Message(s)

After receiving a voice mail message, “

” will flash on the display.

To listen to your voice mail, perform the following steps.

1

Lift the handset or press 

[SP-PHONE/

HEADSET]

 and dial an access phone 

number.

• You will get an access phone number 

from your telephone company.

2

Follow the pre-recorded instructions.

3

When finished, place the handset on the cradle or press

[SP-PHONE/HEADSET]

.

•

“

Voice mail

” and “

” will

 disappear.

• If “

” is still flashing after you have listened to your voice mail message(s), press 

[FUNCTION/EDIT]

, then press and hold 

[ERASE]

 

and “

” will disappear.

When dialing a phone number with the restricted leading digit(s), “

CALL 

RESTRICTED

” will be displayed and not dialed out.

12:34PM 12/15

   Voice mail

10 missed calls

                              

TS600CW_B02.book  Page 44  Tuesday, January 24, 2006  10:57 AM

Summary of Contents for KX-TS600CB

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands