Panasonic KX-TS600CB Operating Instructions Manual Download Page 17

Page: 17 / 56

Basic Operation

To redial the last number dialed

Using the handset:

Lift the handset

press

[REDIAL]

Press

[REDIAL]

Lift the handset.

Using the speakerphone:

Press

[SP-PHONE/HEADSET]

press

[REDIAL]

Press

[REDIAL]

press

[SP-PHONE/

HEADSET]

To redial using the redial list (Memory Redial)

The last 20 phone numbers dialed are stored in the redial list.

1. Press

[REDIAL]

• The last number dialed and “

” are displayed.

• When the number dialed has been stored in the Phonebook,

the name is also displayed.

2. Scroll to the desired number by pressing

[

]

[

]

• You can also scroll through the list by pressing

[REDIAL]

• To exit the list, press

[EXIT]

3. Lift the handset or press

[SP-PHONE/HEADSET]

• To erase an item, repeat steps 1 and 2, and press

[ERASE]

• If “

No items stored

” is displayed, the list is empty.

To adjust the handset volume (4 levels) or the speaker
volume (8 levels) while talking

To increase, press

VOLUME

[

]

. To decrease, press

VOLUME

[

]

• The display shows the volume level for a few seconds.

Example: Handset volume level: 2

Example: Speaker volume level: 3

“

” shows one level.

“

” shows one level.

Loud

Low

????

High

Loud
Low

???

High

TS600CW_B02.book Page 17 Tuesday, January 24, 2006 10:57 AM

Summary of Contents for KX-TS600CB

























































Search results

Summary of Contents for KX-TS600CB

Reviews:

Brands by name

Popular brands

Panasonic KX-TS600CB, Operating Instructions Manual

Search results

Summary of Contents for KX-TS600CB

Reviews:

Brands by name

Popular brands