manualshive.com logo in svg

Panasonic KX-TS600CB, Operating Instructions Manual

Share
Download
Panasonic KX-TS600CB Operating Instructions Manual Download Page 18

Making Calls

18

To put a call on hold

Press 

[HOLD]

.

• The SP-PHONE/HEADSET indicator flashes.
• If using the handset, you can place it on the cradle.
• During the hold, both parties will hear music. For canceling music, see page 40.

To release the hold

If the handset is on the cradle, lift the handset.
If the handset is off the cradle, press 

[HOLD]

.

If using the speakerphone, press 

[SP-PHONE/HEADSET]

.

• If another phone is connected on the same line, you can also release the hold by 

lifting its handset.

Answering Calls

When a call is received, the unit rings, the RINGER indicator flashes 
quickly and “

Incoming call

” is displayed. You can answer a call by 

simply lifting the handset.
If you subscribe to a Call Display service, the calling party’s information will 
be displayed when the unit is ringing (p. 19).

Using the speakerphone

1

Press 

[SP-PHONE/HEADSET]

.

• The indicator lights.

2

Speak into the 

MIC

 (microphone).

3

To hang up, press 

[SP-PHONE/HEADSET]

.

• The indicator light goes out.

• When the ringer volume is set to OFF (p. 13), the unit will not ring.
• The RINGER indicator will flash when 

— a telephone number is dialed in PULSE mode, or
— someone picks up or hangs up another phone connected to the same phone 

line.

This is normal.

TS600CW_B02.book  Page 18  Tuesday, January 24, 2006  10:57 AM

Summary of Contents for KX-TS600CB

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands