manualshive.com logo in svg

Panasonic KX-TDA15, Installation Manual

Share
Download
Panasonic KX-TDA15 Installation Manual Download Page 136

2.10 Starting the Hybrid IP-PBX

136

Installation Manual

2.10 Starting the Hybrid IP-PBX

2.10.1 Starting the Hybrid IP-PBX

CAUTION

•

The SD Memory Card must be inserted in the SD Memory Card slot of the main board before 
startup.

•

Before touching the System Initialise Switch, discharge static electricity by touching ground or 
wearing an earthing strap.

•

Once you have started the Hybrid IP-PBX and if you unplug the Hybrid IP-PBX, do not perform the 
following procedures to start the Hybrid IP-PBX again. Otherwise, your programmed data is 
cleared. To restart the Hybrid IP-PBX, refer to "4.1.4 Using the Reset Button".

•

The Hybrid IP-PBX will continue to be powered even if the power switch is turned "OFF".

•

The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located 
near the equipment and is easily accessible.

System Initialisation Procedure

1.

Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.

Reset Button

System Initialise Switch

RUN Indicator

ALARM Indicator

Summary of Contents for KX-TDA15





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands