Panasonic KX-TCD725EM Operating Instructions Manual Download Page 50

Page: 50 / 100

Call Option

Enter the 4-digit handset PIN (p. 40).

•

The current mode is displayed.

Press

to select “

” or

“

OFF

”, then press

•

A beep sounds and “

” is displayed if

ON is selected.

•

The display will return to “

Call Bar

”. To

return to the standby mode, press
or wait for 60 seconds.

•

After returning to the standby mode, “

”

will go out if OFF is selected.

•

You can exit the programming mode any time
by pressing

Call Prohibition

You can prohibit anyone from making a call with your handset except for emergency calls (999, 112).
Incoming calls are accepted. The factory preset is OFF.
Make sure that the power is ON (p. 12), and the unit is in the standby mode.

Press

until the arrow points to

“

Setting Handset

”, then press

Press

until the arrow points to

“

Call Option

”, then press

While “

Call Bar

” is at the arrow, press

E n t e r H / s e t P I N

1 2 3 4 5 6 7 8 9 0 0

: ----

To set the call prohibition mode ON/OFF

KX-TCD725EM-3(38~64) 01.7.19 10:42 PM Page 50

Summary of Contents for KX-TCD725EM





































































































Search results

Summary of Contents for KX-TCD725EM

Reviews:

Related manuals for KX-TCD725EM

Brands by name

Popular brands

Panasonic KX-TCD725EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD725EM

Reviews:

Related manuals for KX-TCD725EM

Brands by name

Popular brands