Panasonic KX-TCD725EM Operating Instructions Manual Download Page 71

Page: 71 / 100

Chapter 5

Answering System

Press

•

If new message(s) is/are recorded, “

Play

New Msg

” is displayed and pointed by

arrow.

P l a y N e w M s g

N e w P h o n e b o o k

S e t t i n g H a n d s e t

During Playback an/a Incoming/Memo Message

To repeat a message

Press

to display “

Repeat Msg

”, then

press

OR
Press

•

If you press within 5 seconds from start
playback, the previous message will be played.

•

If you press over 5 seconds from start playback,
the current message will be played.

•

The display will return to “

Remote

Operation

”. To return to the standby mode,

press

or wait for 30 seconds.

To skip a message

Press

. Press

until the arrow

points to “

Skip Msg

”, then press

OR
Press

•

The next message will be played if recorded.

•

The display will return to “

Remote

Operation

”. To return to the standby mode,

press

or wait for 30 seconds.

During Playback an/a Greeting/Incoming/Memo Message

To stop answering system operation

Press

. Press

until the arrow points to “

Stop

”, then press

OR
Press

•

The display will return to “

Remote Operation

”. To return to the standby mode, press

wait for 30 seconds.

Quick Play New Message

Make sure that the power is ON (p. 12), and the unit is in the standby mode.

Press

•

New message(s) is/are played back.

•

The unit will announce the remaining
recording time after playback.

•

The display will return to “

Remote

Operation

”. To return to the standby

mode, press

or wait for 30

seconds.

KX-TCD725EM-4(65~85) 01.7.19 10:23 PM Page 71

Summary of Contents for KX-TCD725EM





































































































Search results

Summary of Contents for KX-TCD725EM

Reviews:

Related manuals for KX-TCD725EM

Brands by name

Popular brands

Panasonic KX-TCD725EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD725EM

Reviews:

Related manuals for KX-TCD725EM

Brands by name

Popular brands