manualshive.com logo in svg

Panasonic KX-TCD725EM, Operating Instructions Manual

Share
Download
Panasonic KX-TCD725EM Operating Instructions Manual Download Page 52

52

Other Option

Selecting the Battery Type

Two Nickel Metal-hydride (Ni-MH) batteries are included with this unit. Nickel Cadmium (Ni-Cd)
rechargeable batteries can also be used. If you replace the batteries with Ni-Cd batteries, you must
set the battery type selection to “

Ni-Cd

”, or the battery strength will not be displayed correctly. The

factory preset is “

Ni-MH

”.

Make sure that the power is ON (p. 12), and the unit is in the standby mode.

1

Press 

.

2

Press 

or 

until the arrow points

to “

Setting Handset

”, then press

.

3

Press 

or 

until the arrow points 

to “

Other Option

”, then press 

.

4

Press 

or 

until the arrow points

to “

Battery Type

”, then press 

.

•

The current battery type is at the arrow.

5

Press 

or 

to select “

Ni-Cd

” or

“

Ni-MH

”, then press 

.

•

The display will return to the “

Battery

Type

”. To return to the standby mode,

press 

or wait for 60 seconds.

•

Incorrect battery type selection may shorten
battery life.

In “

Other Option

” menu, Changing the 4-digit handset PIN (p. 40), To set the auto talk

feature ON/OFF (p. 16) are also available.

KX-TCD725EM-3(38~64)  01.7.19 10:42 PM  Page 52

Summary of Contents for KX-TCD725EM





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands