Panasonic KX-TCD725EM Operating Instructions Manual Download Page 62

Page: 62 / 100

Call Restriction

To cancel the call restricted
handset(s)

Follow steps 1 to 3 on Setting the Call
Restriction, then enter the handset
number(s) you desire to cancel.

•

The cancelled handset number(s) stop(s)
flashing.

Press

repeatedly until “

Setting

Base

” is displayed.

•

To return to the standby mode, press

•

You can exit the programming mode any time
by pressing

To cancel the call restriction
number(s)

Follow steps 1 to 3 on Setting the Call
Restriction, then select the call
restricted handset press

Press

repeatedly until the call

restriction number you desire to cancel

is displayed, then erase the number by

pressing

•

The call restriction number is cleared.

Press

repeatedly until “

Setting

Base

” is displayed.

•

To return to the standby mode, press

•

You can exit the programming mode any time
by pressing

KX-TCD725EM-3(38~64) 01.7.19 10:42 PM Page 62

Summary of Contents for KX-TCD725EM





































































































Search results

Summary of Contents for KX-TCD725EM

Reviews:

Brands by name

Popular brands

Panasonic KX-TCD725EM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD725EM

Reviews:

Brands by name

Popular brands