manualshive.com logo in svg

Panasonic KX-T30865, Installation Manual

Share
Download
Panasonic KX-T30865 Installation Manual Download Page 81

2.6 Connection of Extensions

Installation Manual

81

2.6.3

Extra Device Port (XDP) Connection

Any SLT can be connected in parallel with DPT (except KX-T7560 and KX-T7565) as follows:

With KX-T7600 Series DPT

With Other DPTs (except KX-T7560 and KX-T7565)

To a hybrid extension port, 
or DLC4/DLC8 card

DPT

To a hybrid extension port,
or DLC4/DLC8 card

To SLT

4-conductor wiring cord

2-conductor wiring cord

2-conductor wiring cord
Connect pins "T" and "R".

4-conductor wiring cord
Connect pins "T", "R", 
"D1" and "D2".

SLT

TO MAIN UNIT

/ PABX

TO TEL

To a hybrid extension port, 
or DLC4/DLC8 card

DPT

SLT

To a hybrid extension port, 
or DLC4/DLC8 card

To SLT

4-conductor wiring cord

2-conductor wiring cord

2-conductor wiring cord
Connect pins "T" and "R".

4-conductor wiring cord
Connect pins "T", "R", 
"D1" and "D2".

TO TEL

TO EMSS or TO MAIN UNIT

Summary of Contents for KX-T30865

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands