manualshive.com logo in svg

Panasonic KX-T30865, Installation Manual

Share
Download
Panasonic KX-T30865 Installation Manual Download Page 152

3.3 Installation of the KX-TDA Maintenance Console

152

Installation Manual

3.3.3

Hybrid IP-PBX Configuration

This section briefly describes how to check the configuration of the Hybrid IP-PBX using the 
KX-TDA Maintenance Console when PC and the Hybrid IP-PBX are connected by USB cable.
For detailed descriptions of each feature and related PT programming, refer to the on-line help 
at each screen.

1. Start the KX-TDA Maintenance Console 

(refer to "Starting the KX-TDA Maintenance 
Console and Assigning the Basic Items 
(Quick Setup)" in "3.3.1 Installing and 
Starting the KX-TDA Maintenance Console").

2. To check the slot condition of the Hybrid IP-

PBX:

a.

Double-click "Configuration".

b.

Double-click "Slot".

3. To check the PS status:

a.

Double-click "Configuration".

b.

Double-click "Portable Station".

4. To check other configurations, double-click 

the other items in the same manner.

Summary of Contents for KX-T30865

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands