manualshive.com logo in svg

Panasonic KX-T30865, Installation Manual

Share
Download
Panasonic KX-T30865 Installation Manual Download Page 128

2.9 Connection of Doorphones and Door Openers

128

Installation Manual

2.9

Connection of Doorphones and Door 
Openers

2.9.1

Connection of Doorphones and Door Openers

Maximum of 4 doorphones (KX-T30865) and door openers can be connected to the Hybrid IP-
PBX with DPH4 card. Maximum of 2 doorphones (German type) and door openers can be 
connected to the Hybrid IP-PBX with DPH2 card.

Note

Doorphones and door openers are user-supplied.

Maximum Cabling Distance

Current Limit for door opener: 24 V DC/30 V AC, 1 A maximum

Installing the Doorphone (KX-T30865)

1.

Loosen the screw to separate the doorphone into 2 halves.

Diameter       Maximum Distance
0.4 mm:        Under 70 m
0.5 mm:        Under 113 m
0.6 mm:        Under 180 m

Doorphone

Door Opener

Pan

aso

nic

Screw

Summary of Contents for KX-T30865

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands