Panasonic KX-T30865 Installation Manual Download Page 137

Page: 137 / 176

2.10 Connection of Peripherals

Installation Manual

137

PC/Server PC (via USB version 1.1)

The Hybrid IP-PBX is equipped with a USB interface. This interface provides communication
between the Hybrid IP-PBX and a PC or a Server PC.

The PC is used for system programming, diagnostics and external system database storage
(save/load) functions.

The Server PC is used for connecting PCs on a LAN to provide third party call control CTI. The
CTI connection uses the CSTA Phase 3 protocol.

Note

The operating system of the PC or Server PC required for third party call control depends
on your CTI application software. For details, refer to the manual for your CTI application
software.

Pin Assignments

No.

Signal Name

VBUS

USB D-

USB D+

GND

Summary of Contents for KX-T30865

















































































































































































Search results

Summary of Contents for KX-T30865

Reviews:

Brands by name

Popular brands

Panasonic KX-T30865, Installation Manual

Search results

Summary of Contents for KX-T30865

Reviews:

Brands by name

Popular brands