Panasonic KX-T30865 Installation Manual Download Page 102

Page: 102 / 176

2.7 Connection of DECT Portable Stations

102

Installation Manual

Registering the PS

The PS must be registered to the Hybrid IP-PBX by programming both the PS and Hybrid IP-
PBX before it can be used. A PT with multiline display (e.g., KX-T7636 6-line display) is
required for the Hybrid IP-PBX system programming.

Note

For details about system programming using a PT, refer to "2.3.2 PT Programming" and
"3.3 PT Programming" in the Feature Guide.

Entering the Hybrid IP-PBX System Programming Mode Using a PT

Administrator Level

User Level

Note

means default value.

PROGRAM

= 1234

System Password for Administrator—

for PT Programming

Programming No.

3 digits

PROGRAM

= 1234

Programming No.

3 digits

System Password for User—

for PT Programming

Summary of Contents for KX-T30865

















































































































































































Search results

Summary of Contents for KX-T30865

Reviews:

Brands by name

Popular brands

Panasonic KX-T30865, Installation Manual

Search results

Summary of Contents for KX-T30865

Reviews:

Brands by name

Popular brands