Panasonic KX-P7100 Service Manual Download Page 31

Page: 31 / 148

Before handling, remove the Left Cover ( see Section 3.2 ).

3.5. High Voltage Board and Power Supply Unit

3.5.1. High Voltage Board

(1) Remove the screw ( A ) and 5 screws ( B ).

Caution :

Screw ( A ) is different from screws ( B ). When
reinstalling the screw, return it to the original
position.

(2) Disconnect the Flat Cable from the High Voltage Board.

(3) Remove the High Voltage Board, be careful that High

Voltage Terminal Springs are not dropped from the printer
and lost.

(4) Remove the 5 High Voltage Terminal Springs.

Caution :

When

reinstalling

the

High

Voltage

Terminal

Springs, all springs must be returned to the original
position. And the hook of Spring ( A ), ( D ), ( E ) are
set into the slits as shown in the following figure.

KX-P7100

Summary of Contents for KX-P7100




















































































































































Search results

Summary of Contents for KX-P7100

Reviews:

Related manuals for KX-P7100

Brands by name

Popular brands

Panasonic KX-P7100, Service Manual

Search results

Summary of Contents for KX-P7100

Reviews:

Related manuals for KX-P7100

Brands by name

Popular brands