Panasonic KX-P7100 Service Manual Download Page 70

Page: 70 / 148

4.4.17. Internal Engine I / F (Control CPU - Engine CPU)

The communication I/F signal between Control CPU and Engine CPU in main board is as follows.
PPRDY:

Printer Engine had been Powered On.

nPRDY:

Engine status is ready for communication.

nTOP:

A vertical synchronous signal which indicates the home position in a recording sheet.

nHSYNC:

A horizontal synchronous signal which indicates the home position of horizontal laser scanning.

nPRINT:

After receiving this signal from RIP CPU, the engine starts printing. By other words, print request.

nVIDEO:

Video image data which modulate laser beam.

nPURGE:

Paper purge signal which asserted when the paper exit to the tray.

nPSAVE:

Engine power save command signal.

CXD:

Serial command data from RIP to ECU.

SXD:

Serial Status data from ECU to RIP.

nCBSY:

Data transfer busy signal from RIP to ECU.

nSBSY:

Data transfer busy signal from ECU to RIP.

CCLK:

Communication clock for those serial data. ( RIP assert )

KX-P7100

Summary of Contents for KX-P7100




















































































































































Search results

Summary of Contents for KX-P7100

Reviews:

Related manuals for KX-P7100

Brands by name

Popular brands

Panasonic KX-P7100, Service Manual

Search results

Summary of Contents for KX-P7100

Reviews:

Related manuals for KX-P7100

Brands by name

Popular brands