Panasonic KX-NS500 Features Manual Download Page 486

Page: 486 / 580

5.2.2 SIP (Session Initiation Protocol) Extension

Description

This PBX supports the connection of SIP-compatible IP telephones (hardphones and softphones). SIP
extensions make and receive calls using Internet Protocol (IP).
For information about SIP extension compatibility with feature numbers, see 5.5.7 Flexible Numbering/Fixed
Numbering.
For information about Panasonic KX-UT series SIP phones, see 5.2.2.1 KX-UT Series SIP Phones.
For information about Panasonic SIP phones (P-SIP), see 5.2.2.4 Panasonic SIP Phones (P-SIP).
Below are the features supported by SIP extensions:

•

Absent Message (

2.20.2 Absent Message)

•

Account Code Entry (

2.5.4.3 Account Code Entry)

•

Automatic Route Selection (ARS) (

2.8 Automatic Route Selection (ARS) Features)

•

Call Forwarding (FWD) (

2.3.2 Call Forwarding (FWD))

•

Call Hold (

2.13.1 Call Hold)

•

Call Park

(

2.13.2 Call Park)

•

Call Pickup (

2.4.3 Call Pickup)

•

Call Transfer with Announcement (

2.12.1 Call Transfer)

•

Call Waiting Tone (

2.1.3.3 Call Waiting)

•

COLR/CLIR/CLIP/COLP (

4.1.2.2 Calling/Connected Line Identification Presentation (CLIP/COLP))

•

Conference

(

2.14 Conference Features)

•

Conference Group Call (

2.15.1 Conference Group Call)

•

Data Line Security (

2.11.5 Data Line Security)

•

Dial Information (CTI) (

2.26.1 Computer Telephony Integration (CTI))

•

Direct Inward System Access (DISA) (

2.16.1 Direct Inward System Access (DISA))

•

Door Open (

2.18.2 Door Open)

•

Doorphone Call (

2.18.1 Doorphone Call)

•

Emergency Call (

2.5.4.2 Emergency Call)

•

Executive Busy Override Deny (

2.10.2 Executive Busy Override)

•

Extension Dial Lock (

2.7.3 Extension Dial Lock)

•

Extension Feature Clear (

2.24.2 Extension Feature Clear)

•

Extension PIN (

2.24.1 Extension Personal Identification Number (PIN))

•

External BGM On/Off (

2.30.1 Background Music (BGM))

•

FWD/DND (

2.3 Call Forwarding (FWD)/Do Not Disturb (DND) Features)

•

Group FWD (

2.3.2 Call Forwarding (FWD))

•

Idle Line Access (

2.5.5.3 Trunk Access)

•

Log-in/Log-out (

2.2.2.8 Log-in/Log-out)

•

Message Waiting (

2.20.1 Message Waiting)

•

Not Ready (

2.2.2.8 Log-in/Log-out)

•

Operator Call (

5.1.5 Operator Features)

•

Paging (

2.17.1 Paging)

•

Personal Speed Dialling (

2.6.4 Speed Dialling—Personal/System)

•

Quick Dialling (

2.6.5 Quick Dialling)

•

Redial (

2.6.3 Last Number Redial)

•

Remote Station Lock (

2.7.3 Extension Dial Lock)

•

S-CO Line Access (

2.5.5.3 Trunk Access)

•

System Speed Dialling (

2.6.4 Speed Dialling—Personal/System)

•

TIE Line Call (

4.3.1 TIE Line Service)

•

Time Service (

5.1.4 Time Service)

•

Timed Reminder (

2.24.4 Timed Reminder)

486

Feature Guide

5.2.2 SIP (Session Initiation Protocol) Extension

Summary of Contents for KX-NS500





































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for KX-NS500

Reviews:

Related manuals for KX-NS500

Brands by name

Popular brands

Panasonic KX-NS500, Features Manual

Search results

Summary of Contents for KX-NS500

Reviews:

Related manuals for KX-NS500

Brands by name

Popular brands