Panasonic KX-FP701LA Service Manual Download | Manualshive

Page: 123 / 207

background image

123

KX-FP701LA

12.5.6.2. Defective ITS (Integrated Telephone System) Section

1. No handset transmission / reception and no monitor reception

Perform a signal test in the

ITS or the NCU section

and locate a defective point (where the signal disappears) on each route

between the handset microphone and telephone line (sending), or between the telephone line and the handset speaker (receiv-
ing), or between the microphone and the telephone line (sending), or between the telephone line and the speaker (receiving).
Check the components at that point.

12.5.6.1.Check Sheet for Signal Route

(P.122) is useful for this investigation.

2. No pulse dialing

3. No ring tone (or No bell)

REFERENCE:

12.5.6.1.Check Sheet for Signal Route

(P.122)

6.7.NCU Section

(P.43)

4. No tone dialing

REFERENCE:

12.5.6.1.Check Sheet for Signal Route

(P.122)

«
...
121
122
123
124
125
...
»

Summary of Contents for KX-FP701LA
















































































































































































































Reviews:

No comments

Related manuals for KX-FP701LA

Brand: Fellowes Pages: 4

Brand: DURKOPP ADLER Pages: 46

Brand: Singer Pages: 8

OFX 500 LINKFAX

Brand: Olivetti Pages: 230

Brand: Pacific Pages: 8

Brand: Unicorn Pages: 18

Brand: Royal Vendors Pages: 76

Brand: Pacific Pages: 8

Brand: Opus Pages: 16

Brand: Kärcher Pages: 261

Brand: Lafferty Pages: 16

Brand: HTC Pages: 56

ellegante 2 BLG2

Brand: Baby Lock Pages: 8

Brand: JUKI Pages: 80

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 43

Brand: Panasonic Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands