manualshive.com logo in svg

Panasonic KX-FP701LA, Service Manual, Page: 10 / 207

Share
Download
Panasonic KX-FP701LA Service Manual Download Page 10

10

KX-FP701LA

4.1.3.

Other

4.2.

Optional Accessories

*1

 To ensure the unit operates properly, we recommend using the Panasonic replacement film.

The ink film is not reusable. Do not rewind and use the ink film again.

5 Features

General

• LCD (Liquid Crystal Display) readout

Plain Paper Facsimile Machine

• 12 second transmission speed*
• A4, Letter, G3 compatible
• Automatic document feeder (up to 10 sheets)
• Quick scan
• Resolution: Standard/Fine/Super fine/Photo (64 level)
• Broadcast
• 50-sheet recording paper capacity
• Automatic fax/phone switching
• Distinctive ring detection **

* The 12 second speed is based upon the ITU-T No. 1 Test
Chart on the condition that memory transmission is performed.
** Subscription to distinctive ring services is required.

Large Memory... Performed by DRAM

Approx. 28 pages of memory reception
Approx. 25 pages of memory transmission

Integrated Telephone System

• On-hook dialing
• Voice muting
• Redialing function
• 106-station telephone directory with Phonebook
• Caller ID service

This unit is compatible with the Caller ID service offered by
your local telephone company. To use this unit’s Caller ID
features, you must subscribe to Caller ID service.
Important:

- This unit will only display the caller’s telephone number

and name.

- This unit will not support future additional telephone ser-

vices.

- Depending on the service of the local telephone com-

pany, the date/time of the call or the caller’s name may
not be displayed.

Make sure the following ring count is set to 2 or more rings
beforehand.

- FAX ring count (feature #06 on P.97) 
- The name display service may not be available in some

areas. For further information, please contact your tele-
phone company.

Enhanced Copier Function

• Multi-copy function (up to 50 copies)
• Enlargement and reduction
• Collate
• 64-Level halftone

Model No.

Description

Specification

KX-FA57A

 Replacement Film

*1

 70 m 

×

 1 rolls

(Prints about 225 Letter-sized pages)

Summary of Contents for KX-FP701LA
















































































































































































































Reviews:

No comments