Panasonic KX-FP701LA Page 21 Service Manual Download | Manualshive

Page: 21 / 207

background image

21

KX-FP701LA

6.3.7.

RTC Backup Circuit

1.

Function

This unit has a lithium battery (BAT401) which works for Real Time Clock IC (RTC: inside IC1).
The RTC continues to work, backed up by a lithium battery even when the power switch is OFF.
The user parameters for autodial numbers, the system setup data and others are in the FLASH MEMORY (IC6).

2.

RTC Inside (IC1) Backup Circuit Operation

When the power switch is turned ON, power is supplied through Q7 to the RTC (inside IC1). At this time, the voltage at pin 14
of the IC1 is +2.5V. When the power switch is turned OFF, the BAT401 supplies power to RTC through D407 and Q505. The
voltage at pin 14 of IC1 is about +2.2V. When the power switch is OFF and the voltage of +3.3V decreases, pin 14 of RTC
(IC1) becomes roughly the same voltage as the battery voltage. RTC goes into the backup mode, in which the power con-
sumption is lower.

«
...
19
20
21
22
23
...
»

Summary of Contents for KX-FP701LA
















































































































































































































Reviews:

No comments

Related manuals for KX-FP701LA

Brand: Pacific Pages: 8

Brand: Oki Pages: 248

Brand: Jack Pages: 42

Brand: Garudan Pages: 89

Brand: Kärcher Pages: 260

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 82

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 86

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 108

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 110

Brand: Panasonic Pages: 150

Brand: Panasonic Pages: 114

Brand: Panasonic Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands