151
KX-FP701LA
15.1.2.1. Maintenance List
15.1.2.2. Maintenance Cycle
Note:
*
1
These values are standard and may vary depending on usage conditions.
*
2
Refer to
20.1.Cabinet, Mechanical and Electrical Parts Location
(P.193).
No.
OPERATION
CHECK
REMARKS
1
Document Path
Remove any foreign matter such as paper.
—
2
Rollers
If the roller is dirty, clean it with a damp cloth then dry thor-
oughly.
Refer to
15.4.1.Document feeder/recording
paper feeder/scanner glass cleaning
(P.159).
3
Platen Roller
If the platen is dirty, clean it with a damp cloth then dry
thoroughly. Remove the paper and film cartridge before
cleaning.
—
4
Thermal Head
If the thermal head is dirty, clean the printing surface with a
cloth moistened with denatured alcohol (alcohol without
water), then dry thoroughly.
Refer to
15.4.2.Thermal Head Cleaning
(P.160).
5
Sensors
Document top sensor (SW337), Document set sensor
(SW338), Cover open sensor (SW502), Paper top sensor
(SW502), Film detection sensor (SW501), Film end sensor
(SW1003) . Confirm the operation of the sensors.
See
15.1.2.Maintenance Check Items/Compo-
nent Locations
(P.150) and
14.2.11.HOW TO
REMOVE THE DIGITAL, ANALOG, SENSOR
BOARDS
(P.145).
6
Glass
If the glass is dirty, clean them with a dry soft cloth.
Refer to
15.4.1.Document feeder/recording
paper feeder/scanner glass cleaning
(P.159).
7
Abnormal, wear and tear
or loose parts
Replace the part. Check if the screws are tight on all parts.
—
No.
Item
Cleaning Cycle
Replacement
Cycle
Procedure
1
Separation Roller (Ref. No. 145)*
2
3 months
7 years*
1
(31,500 documents) Refer to
14.2.13.HOW TO REMOVE THE
MOTOR BLOCK AND SEPARATION ROLLER
(P.147).
2
Separation Rubber (Ref. No. 13)
3 months
7 years (31,500 documents) Refer to
15.4.1.Document feeder/recording
paper feeder/scanner glass cleaning
(P.159).
3
Feed Rollers (Ref. No. 11, 56, 94)
3 months
7 years (31,500 documents) Refer to
14Disassembly and Assembly
Instructions
(P.133).
4
Thermal Head (Ref. No. 40)
3 months
7 years (31,500 documents) Refer to
14.2.6.HOW TO REMOVE THE THER-
MAL HEAD
(P.140).
5
Platen Roller (Ref. No. 90)
3 months
7 years (31,500 documents) Refer to
14.2.7.HOW TO REMOVE THE
PLATEN ROLLER AND BACK COVER
(P.141).
6
Pickup Roller (Ref. No. 96)
3 months
7 years (31,500 documents) Refer to
14.2.8.HOW TO REMOVE THE PICKUP
ROLLER
(P.142).
Summary of Contents for KX-FP701LA
