Panasonic KX-FP200 Operating Instructions Manual Download | Manualshive

Page: 59 / 80

background image

DISPLAY MESSAGE

CAUSE AND REMEDY

59

Troubleshooting

and Routine Care

Error messages on the display

If the unit detects a problem, one or more of the following messages will appear on the display.

¡

There is something wrong with the unit. Contact our service personnel (p. 72).

¡

The front cover is open. Close it.

¡

The document is not fed into the unit properly. Reinsert the document. If
misfeeding occurs frequently, clean the document feeder rollers inside the unit
(p. 69). If the problem remains, adjust the feeder pressure (p. 66).

¡

The film cartridge is not inserted properly. Reinsert it correctly (p. 67, 68).

¡

The recording paper lever is released. Push it back to set the lever (p. 9).

¡

Memory (phone numbers, parameters, etc.) has been erased. Re-program.

¡

The recording paper is not installed or the unit ran out of paper. Install paper
(p. 8).

¡

The recording paper is not fed into the unit properly or has jammed near the
recording paper entrance. Clear the jammed paper (see “When paper has
jammed near the recording paper entrance” on page 65).
Do not install folded or heavily curled paper in the paper tray.

¡

The unit has (a) document(s) in memory. See the other message’s instructions to
print out the document(s).

¡

The film is empty. Replace the film or film cartridge with a new one (p. 67, 68).

¡

The film is slack. Tighten it (see step 8 on page 68) and install again.

¡

The remaining film can print approx. 15 pages of letter size documents. Prepare a
new film or film cartridge (p. 6).

¡

The memory is full of received documents due to a lack of recording paper or a
recording paper jam, etc. Install paper or clear the jammed paper.

¡

When performing memory or multistation transmission, the document being stored
exceeds the memory capacity of the unit. Transmit the entire document by using
manual or automatic transmission.

¡

The receiving unit is busy or ran out of recording paper. Try again.

¡

A recording paper jam occurred under the film cartridge. Clear the jammed paper
(p. 64).

¡

The unit is checking if the film is set correctly. Wait for a while.

CHECK COVER

CHECK DOCUMENT

CHECK MEMORY

MEMORY FULL

NO RESPONSE

PAPER JAMMED

CHECK FILM

CHECK LEVER

CHECK PAPER

FAX IN MEMORY

FILM EMPTY

FILM NEAR EMPTY

CALL SERVICE

(continued)

PLEASE WAIT

Troubleshooting

«
...
57
58
59
60
61
...
»

Summary of Contents for KX-FP200

















































































Reviews:

No comments

Related manuals for KX-FP200

Brand: Pfaff Pages: 122

Brand: Pfaff Pages: 88

Brand: weasy Pages: 75

Brand: U-Line Pages: 12

Brand: Radio Shack Pages: 32

Brand: TAJIMA Pages: 140

Terra 3700B 908 4203 010

Brand: Nilfisk-Advance Pages: 68

Brand: Singer Pages: 13

Brand: Numatic Pages: 16

Brand: Panasonic Pages: 100

Brand: Beko Pages: 40

Brand: Beko Pages: 36

Brand: Baby Lock Pages: 25

DDL-9000C-S Series

Brand: JUKI Pages: 113

Brand: Husqvarna Viking Pages: 40

Brand: Husqvarna Viking Pages: 64

Brand: Brother Pages: 2

Brand: Brother Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands