Panasonic GT32-R User Manual Download Page 45 | Manualshive

Page: 45 / 206

background image

2-5

○

1

Touch screen

Various screens are displayed here. A touch panel is provided on the liquid crystal display panel, and
switches can be operated and data entered simply by touching the panel.
Optional protective sheets are also available to protect the touch panel and keep it clean.
(A sheet is affixed to the touch panel to protect it from scratches when shipping. Please remove it before
using the GT.)

○

2

SD memory card slot

A SD memory card is inserted in this slot.

-

Saving from GTWIN: Operate on the GTWIN screen using a SD memory card read/writer.

-

Saving from GT main unit: Operate on the SD memory card setting screen under the system menu.

○

3

USB port

This is a connector for connecting the screen creation tool. The commercial USB cable can be used.

○

4

SD memory access lamp

The lamp turns on while accessing a SD memory card.

○

5

Battery cover

When using a backup battery to be separately purchased, open this battery cover to install it.
The clock, PLC device hold data, alarm history and GT internal device hold data functions can be used
with the backup battery.

○

6

Operation mode setting switches

Setting the operation mode setting switches as follows when turning on the power supply enables the
setting to inhibit to move to the system menu or enables to clear F-ROM.

Setting

Normal use
(Factory default)

Inhibit system
menu shift

Clear F-ROM

Switch setting

The screen (backlight) flashes for a while when the F-ROM clear is executed.
Once the F-ROM clear is complete, the buzzer sounds and "Memory is cleared" is displayed on the
screen. Set the operation mode setting switches to the state in the normal use after confirming this
message, and turn on the power again.
Do not use any settings other than the above settings.

○

7

Mounting location of connector for battery

○

8

COM port (PLC/external device connection port) and power supply terminal

This is a communication port (RS232C or RS422) for connecting to a PLC, host PC, or microcomputer
board, and a power supply terminal for operation.

○

9

Waterproof packing

This assures that the front panel is waterproof.

«
...
43
44
45
46
47
...
»

Summary of Contents for GT32-R















































































































































































































Reviews:

No comments

Related manuals for GT32-R

Brand: Hanns.G Pages: 21

Brand: Hanns.G Pages: 1

Brand: Falcon Pages: 16

Brand: Kodak Pages: 6

Brand: Fametech Pages: 23

Brand: Larsen & Toubro Pages: 168

Brand: DAEWOO ELECTRONICS Pages: 53

Brand: Daktronics Pages: 63

Brand: 7starlake Pages: 10

Brand: Pixio Pages: 12

Brand: Tandy Pages: 45

Brand: ROVARY Pages: 38

Brand: EverFocus Pages: 1

Brand: Viotek Pages: 20

Brand: Eizo Pages: 73

Brand: Proteus Pages: 11

Brand: Viotek Pages: 20

Brand: Omron Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands