manualshive.com logo in svg

Panasonic GT32-R, User Manual

The Panasonic GT32-R user manual is available for free download from manualshive.com. Gain comprehensive knowledge on operating and maximizing the potential of your Panasonic GT32-R with this detailed manual. Get step-by-step instructions, troubleshooting tips, and explore all the features and functionalities of this remarkable product.

Share
Download
background image

Safety Precautions 

Observe the following notices to ensure personal safety or to prevent accidents. 
To ensure that you use this product correctly, read this User’s Manual thoroughly before use. 
Make sure that you fully understand the product and information on safety. 
This manual uses two safety flags to indicate different levels of danger. 

WARNING   

If critical situations that could lead to user’s death or serious injury is assumed by 
mishandling of the product:

 

- Always take precautions to ensure the overall safety of your system, so that the whole 

system remains safe in the event of failure of this product or other external factor. 

- DO NOT USE THE PROGRAMMABLE DISPLAY TO CONTROL SAFETY FEATURES OR 

OTHER CRITICAL OPERATIONS OF EQUIPMENT OR SYSTEMS. A COMMUNICATION 
ERROR (FOR ANY REASON) MIGHT PREVENT SUCH SAFETY FEATURES OR 
CRITICAL OPERATIONS FROM FUNCTIONING PROPERLY. 

- Do not use this product in areas with inflammable gas. It could lead to an explosion. 
- Exposing this product to excessive heat or open flames could cause damage to the lithium 

battery or other electronic parts. 

- Battery may explode if mistreated. Do not recharge, disassemble or dispose of fire. 

CAUTION   

If critical situations that could lead to user’s injury or only property damage is 
assumed by mishandling of the product.

 

- To prevent excessive exothermic heat or smoke generation, use this product at the values 

less than the maximum of the characteristics and performance that are assured in these 
specifications. 

- Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke 

generation. 

- Do not touch the terminal while turning on electricity. It could lead to an electric shock. 
- Use the external devices to function the emergency stop and interlock circuit. 
- Connect the wires or connectors securely.   

The loose connection could cause excessive exothermic heat or smoke generation. 

- Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside 

of the product. It could cause excessive exothermic heat or smoke generation. 

- Do not undertake construction (such as connection and disconnection) while the power 

supply is on. It could lead to an electric shock. 

- The control force of the touch switches should be less than the specification of the product. 

Failure to do so could lead to a damage to the product or a personal injury. 

- These touch switches operate using analog resistance membrane. Do not press more than 

one point on the screen at a time. Doing so might operate a switch located in the middle of 
the points pressed if one exists, and could lead to a damage to the facility or an accident. 

 

Copyright / Trademarks 

- This manual and its contents are copyrighted. 
- You may not copy this manual in whole or part, without written consent of Panasonic 

Industrial Devices SUNX Co., Ltd. 

- Windows is a registered trademark of Microsoft Corporation in the United States and other 

countries. 

- Ethernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corp. 
- SDHC logo and SD logo are trademarks. 
- All other company names and product names are trademarks or registered trademarks of 

their respective owners. 

POT_GT

 

Summary of Contents for GT32-R















































































































































































































Reviews:

No comments

Related manuals for GT32-R

Samsung LD190N - LCD Monitor 1360X768 5MS Analog Manual Del Usuario preview
LD190N - LCD Monitor 1360X768 5MS Analog
Brand: Samsung Pages: 47
Samsung 971P - SyncMaster - 19" LCD Monitor Owner'S Manual preview
971P - SyncMaster - 19" LCD Monitor
Brand: Samsung Pages: 56
Panasonic TH37PR10U - 37" PLASMA TELEVISION Operating Instructions Manual preview
TH37PR10U - 37" PLASMA TELEVISION
Brand: Panasonic Pages: 48
Samsung FP-T5894W Manual Del Usuario preview
FP-T5894W
Brand: Samsung Pages: 80
Panasonic TH-55AF1U Operating Instructions Manual preview
TH-55AF1U
Brand: Panasonic Pages: 32
IBM ThinkVision L190N User Manual preview
ThinkVision L190N
Brand: IBM Pages: 42
Yaesu SM-5000 - APRS Manual preview
SM-5000 - APRS
Brand: Yaesu Pages: 8
I-Tech iNAP-1700 User Manual preview
iNAP-1700
Brand: I-Tech Pages: 27
Citizen CH-611C Instruction Manual preview
CH-611C
Brand: Citizen Pages: 12
Hanns.G HH251HPB Specifications preview
HH251HPB
Brand: Hanns.G Pages: 2
Prestigio PPM101FHD16 User Manual preview
PPM101FHD16
Brand: Prestigio Pages: 26
ViewSonic E96f+SB-1 Service Manual preview
E96f+SB-1
Brand: ViewSonic Pages: 59
Olorin VistaLine Series User Manual preview
VistaLine Series
Brand: Olorin Pages: 49
Marshall Electronics V-R171P-4A Operating Manual preview
V-R171P-4A
Brand: Marshall Electronics Pages: 2
Van Mechelen Partner LM15 User Manual preview
Partner LM15
Brand: Van Mechelen Pages: 19
Polar Electro WearLink Transmitter Nike+ User Manual preview
WearLink Transmitter Nike+
Brand: Polar Electro Pages: 8
Elmo LCM4N Specifications preview
LCM4N
Brand: Elmo Pages: 1
AOC 7F-SLK User Manual preview
7F-SLK
Brand: AOC Pages: 17

Brands by name

Popular brands

Load more brands