Panasonic GT32-R User Manual Download Page 146

Page: 146 / 206

6-6

6.2 GT02

6.2.1 General Specifications (GT02)

Item

Specifications

24 V DC type

5 V DC

Rated voltage

24 V DC

5 V DC

Operating voltage range

21.6 to 26.4 V DC

4.5 to 5.5 V DC

Power consumption

1.9 W or less (80 mA or less)

1W or less
(200 mA or less)

Note1)

Ambient temperature

0 to +50



Ambient humidity

20 to 85% RH (at 25



C), non-condensing

Storage temperature

-20 to +60



Storage humidity

10 to 85% RH (at 25



C), non-condensing

Breakdown voltage

Between [power supply terminals] and [case]
500 V AC for 1 minute, Cutoff current 10mA (at default setting)

Insulation resistance

Between [power supply terminals] and [case]
100 M



or more, 500 V DC, measured with megohmmeter (at default

setting)

Vibration resistance

5 to 8.4 Hz half amplitude 3.5 mm,
8.4 to 150 Hz acceleration 9.8 m/s

10 sweeps each in X, Y and Z directions (1 octave/min)

Shock resistance

147 m/s

, 3 times on 3 axes

EC Directive applicable

EN61131-2 (EMC Directive)

Noise immunity

1000 V [P-P] or more, Pulse width 50 ns, 1



s between power supply

terminals (based on in-house measurements)

Note2)

Protective construction

IP67 (Initial value, evaluated by us)
Dustproof and drip-proof from front panel only (packing used on panel
contact surface)

Note3)

Weight

Approx. 170 g

Note1) When supplying the power from the TOOL port of a PLC (CPU unit), confirm the PLC restrictions

such as the power supply capacity before use.

Note2) When using our exclusive cable.
Note3) When reattaching, replace waterproof packing.

Summary of Contents for GT32-R















































































































































































































Search results

Summary of Contents for GT32-R

Reviews:

Related manuals for GT32-R

Brands by name

Popular brands

Panasonic GT32-R, User Manual

Search results

Summary of Contents for GT32-R

Reviews:

Related manuals for GT32-R

Brands by name

Popular brands