Panasonic GT32-R User Manual Download Page 183

Page: 183 / 206

6-43

6.11 GT32-E

6.11.1 General Specifications (GT32-E)

Item

Specifications

GT32M-E

GT32T-E

Rated voltage

24 V DC

Operating voltage range

21.6 to 26.4 V DC

Power consumption

4.8 W or less (200 mA or less)

7.2 W or less (300 mA or less)

Insulation method of
power supply part

Transformer insulation

Ambient temperature

-20 to +60



Note1)

Ambient humidity

10 to 90% RH (at 25



C), non-condensing

Storage temperature

-20 to +60



Storage humidity

10 to 90% RH (at 25



C), non-condensing

Breakdown voltage

Note2)

Between [power supply terminals] and [case]
500 V AC for 1 minute, Cutoff current 10mA (at default setting)

Insulation resistance

Between [power supply terminals] and [case]
100 M



or more, 500 V DC, measured with megohmmeter (at default

setting)

Vibration resistance

5 to 8.4 Hz half amplitude 3.5 mm
8.4 to 150 Hz acceleration 9.8 m/s2,
10 sweeps each in X, Y and Z directions (1 octave/min)

Shock resistance

147 m/s

, 4 times on 3 axes

EC Directive applicable

EN61131-2 (EMC Directive)

Noise immunity

1000 V [P-P] or more, Pulse width 50 ns, 1



s between power supply

terminals (based on in-house measurements)

Note3)

Electrostatic discharge
resistance

6kV
(Contact Discharge, EN61000-4-2 Level 3)

Protective construction

IP67 (Initial value, evaluated by us)
Dustproof and drip-proof from front panel only (packing used on panel
contact surface)

Note4)

Weight

Approx. 470 g

Note1) When it is installed in horizontal orientation (installed to make the liquid crystal face be topside),

installed upright in vertical orientation or when using a battery, the usable range is -20 to +55



Note2) Not isolated between the USB port, COM port and the internal digital circuit.
Note3) When using our exclusive cable.
Note4) When reattaching, replace waterproof packing.

Summary of Contents for GT32-R















































































































































































































Search results

Summary of Contents for GT32-R

Reviews:

Related manuals for GT32-R

Brands by name

Popular brands

Panasonic GT32-R, User Manual

Search results

Summary of Contents for GT32-R

Reviews:

Related manuals for GT32-R

Brands by name

Popular brands