92
RQT9089
Messages
On the Unit’s Display
Page
H
, F
(“ ” stands for a service number.)
An error has occurred. The number following “H” or “F” depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
(
➔
94, “To restore the unit if it freezes” ).
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
•
•
−
−
DVD
(“ ” stands for a number.)
The remote control and the main unit are using different codes. Change the
code on the remote control.
•
94
GUIDE
GUIDE Plus+ data is being downloaded.
•
84
HARD ERR
If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
•
−
NoCASSETTE
You have not inserted a video cassette for the recording.
•
89
NoERAS
You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
•
−
NoREAD
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
The disc may be incompatible or of poor quality.
You have used a lens cleaner and it has finished operation. Press
[
;
OPEN/CLOSE] on the main unit to eject the disc.
•
•
•
6
15, 16
7
NoWRIT
You cannot write to this disc.
The disc may be damaged. Use a new disc.
•
−
FINAL
When the screen asking if you want to finalise the disc appears, the message
is displayed.
•
29
PLEASE WAIT
Displayed when the unit is started. This is not a malfunction.
The unit is carrying out its recovery process. You cannot operate the unit while
•
•
−
−
PROG FULL
There are already 32 timer recording programmes. Delete unnecessary timer
recording programmes.
•
35
PROTECT
You have inserted a video cassette without the accidental erasure prevention
tab. Use a video cassette with an accidental erasure prevention tab.
•
89
REMOVE
The USB device is drawing too much power. Remove the USB device.
•
−
SP 35:50, LP 151h
(“SP”, ”LP” and the numbers are
examples.)
Available space on the HDD or disc.
The example “SP 35:50” is displayed when less than 100 hours are available
and the example “LP 151h” is displayed when over 100 hours are available.
“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes” and
“151h” means “151 hours”.
•
−
SW-DL
The unit is performing a software update.
•
84
UNSUPPORT
You have inserted a disc the unit cannot play or record onto.
You tried to operate with a non-compatible USB memory.
•
•
15, 16
17
UNFORMAT
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R, +R DL
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
•
76
F74
The HDMI connection could not be authenticated due to a transfer malfunction.
Consult the dealer where the unit was purchased.
•
−
F75
The HDMI connection could not be authenticated due to an internal data malfunction.
Consult the dealer where the unit was purchased.
•
−
U59
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
•
−
U61
(When a disc is not inserted) Displays when a malfunction has occurred
during recording, playback or copy to VHS etc. This is displayed when the unit
is in the recovery process to return to normal operation; it is not broken. Once
the display disappears you can use the unit again.
•
−
U76
HDMI cannot be output because you are connected to a model that does not
support copyright protection.
•
−
U80
U81
U99
The unit fails to operate properly. Press [
^
/I] on the main unit to switch the unit
to standby mode. Press [
^
/I] on the main unit again to turn the unit on.
•
−
U88
There was something unusual detected with the disc while recording, playing or copying;
there was a power failure or the AC mains lead was disconnected while the unit was on.
The unit is carrying out its recovery process. This process restores the unit to normal
operation. The unit is not broken. Wait until the message disappears.
•
96
X HOLD
The Child Lock function is activated.
Press and hold [OK] and [RETURN] at the same time until “X HOLD” disappears.
•
85
The message is alternately displayed.
RQT9089-B̲DMR-EX98V̲EB.indb 92
RQT9089-B̲DMR-EX98V̲EB.indb 92
2008/04/23 19:01:35
2008/04/23 19:01:35
