Panasonic CS-PC12QKH Service Manual Download Page 47

Page: 47 / 115

11.3.6 Piping

Insulation

1 Please carry out insulation at pipe connection portion as mentioned in Indoor/Outdoor Unit Installation

Diagram. Please wrap the insulated piping end to prevent water from going inside the piping.

2 If drain hose or connecting piping is in the room (where dew may form), please increase the insulation by

using POLY-E FOAM with thickness 6 mm or above.

11.3.6.1 Cutting

and

Flaring the Piping

1 Please cut using pipe cutter and then remove the burrs.
2 Remove the burrs by using reamer. If burrs is not removed, gas leakage may be caused. Turn the piping end

down to avoid the metal powder entering the pipe.

3 Please make flare after inserting the flare nut onto the copper pipes.

Summary of Contents for CS-PC12QKH




















































































































Search results

Summary of Contents for CS-PC12QKH

Reviews:

Related manuals for CS-PC12QKH

Brands by name

Popular brands

Panasonic CS-PC12QKH, Service Manual

Search results

Summary of Contents for CS-PC12QKH

Reviews:

Related manuals for CS-PC12QKH

Brands by name

Popular brands