Panasonic CS-PC12QKH Service Manual Download Page 63

Page: 63 / 115

13.5 Outdoor Fan Speed Control



Outdoor fan speed can be changes to Hi or Lo according to outdoor temperature. (For PC24/28QKH)



There is only one speed for outdoor fan motor. (For PC9/12/18QKH)



When the air conditioner is turned on, the compressor and the outdoor fan will operate simultaneously.



Likewise, both compressor and outdoor fan will stop at the same time if the unit is turned off.

13.6 Vertical Airflow Direction Control

13.6.1 Auto

Control



When the vertical airflow direction is set to Auto using the remote control, the louver swings up and down as

shown in the diagram.



When stops operation using the remote control, the discharge vent is reset and stops at the closing position.



During Cooling operation or Soft Dry operation, indoor fan motor may stop to rotate at certain periods. At that

condition, the louver will stop swinging.

(For PC9/12QKH)

(For PC18/24/28QKH)

Summary of Contents for CS-PC12QKH




















































































































Search results

Summary of Contents for CS-PC12QKH

Reviews:

Brands by name

Popular brands

Panasonic CS-PC12QKH, Service Manual

Search results

Summary of Contents for CS-PC12QKH

Reviews:

Brands by name

Popular brands