Panasonic CF-61 Series Operating Instructions Manual Download Page 26 | Manualshive

Page: 26 / 50

background image

26

Battery Pack

Replacing the Battery pack

Mounting

1

2

Top Button

Bottom Button

Removal

With the label facing up, insert the battery pack into the com-
puter until it clicks into place.

press and slide the bottom button to the direction indicated.

2

Slide the top button up, and

1

Always switch the computer off and disconnect the AC adaptor before replacing the battery

pack.

If the computer is in the suspend mode, the system data will be preserved for a maximum of 3

minutes when the battery pack is removed. Make sure to attach the new battery pack within
this time.

NOTE

If the power stored in the battery pack reaches a low level while the computer is
being run off the battery pack, the battery indicator lights red and repeated beeps
sound from the speakers. Should this occur, either immediately connect the AC adaptor
or replace the battery pack with a fully charged one.
The battery pack is a consumable item. If the amount of time the computer can be
run off a particular battery pack becomes dramatically shorter, and repeated
rechargings do not restore its performance, the battery pack should be replaced with
a new one (part number: CF-VZS611).

Pull out the battery pack.

«
...
24
25
26
27
28
...
»

Summary of Contents for CF-61 Series



















































Reviews:

No comments

Related manuals for CF-61 Series

ToughBook CF-72 Series

Brand: Panasonic Pages: 8

Toughbook CF-H2

Brand: Panasonic Pages: 36

Toughbook CF-H1CSLFZ6M

Brand: Panasonic Pages: 106

Brand: Gateway Pages: 164

Brand: Compaq Pages: 69

Brand: Asus Pages: 2

Brand: Acorn Pages: 114

Brand: Advanced Micro Computers Pages: 77

VAIO VGN-UX180P

Brand: Sony Pages: 2

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

VAIO VGN-SZ680ND

Brand: Sony Pages: 2

Vaio VGN-UX27CN

Brand: Sony Pages: 23

VAIO VGN-UX180P

Brand: Sony Pages: 22

VAIO VGN-TX700 Series

Brand: Sony Pages: 24

Vaio VGN-T16RLPS

Brand: Sony Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands