Panasonic AW-UN70KE Operating Instructions Manual Download | Manualshive

Page: 130 / 144

background image

130

Troubleshooting

(continued)

Symptom

Cause and remedial action

Reference

pages

The unit turns in the
opposite direction to
the one operated

●

Has the stand‑alone (Desktop) installation setting been selected
correctly?

P.48, P.87

●

The reversal setting may have been established at the controller if
the unit is connected to the controller.



Refer to the Operating Instructions of the controller.

–––

No access is possible
from the web browser

●

Has a LAN cable of category 5 or above been connected to the LAN
connector for IP control?

<Basics>

P.23

●

Is the [LINK] LED of the LAN connector for IP control lit?



If it is not lit, it means that something is wrong with the connection

to the LAN or that the network at the connection destination is not
working properly.
Check the LAN cable for defective contacts, and check the wiring.

<Basics>

P.23

●

Is the power on?



If the unit’s status display lamp is off or if it has lit up orange,

it means that the unit’s power is not being supplied.

P.7

●

Has a valid IP address been set in the unit?

P.92

●

Has the wrong IP address been accessed?



Check the connections by following the steps below.

[When using Windows]

Using the Windows command prompt, execute
  > ping [IP address which has been set in the camera]
A reply returned from the unit signifies that there are no problems in
operation.
If a reply is not received, try following operation:
•   Reboot the unit, and within 20 minutes change the IP address

using the Easy IP Setup Software.

[When using Mac]

Using the OS X terminal, execute
  > ping -c 10 [IP address which has been set in the camera]
A reply returned from the unit signifies that there are no problems in
operation.
If a reply is not received, try following operation:
•   Reboot the unit, and within 20 minutes change the IP address

using the Easy IP Setup Software.

–––

●

Has 554 been set as the HTTP port number?



Use any port number, except for the numbers below which are used

by the unit, for the HTTP port number.
20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161, 162, 443, 554, 995,
10669, 10670, 59000 to 59999, 60000 to 61000

P.95

●

Is access being performed in HTTPS mode?



For details on when [HTTPS] - [Connection] (page 100) is set

to [HTTPS] in the [Advanced] tab of the [Network] screen, see
“Accessing the Camera by HTTPS”.

P.106

«
...
128
129
130
131
132
...
»

Summary of Contents for AW-UN70KE

















































































































































Reviews:

No comments

Related manuals for AW-UN70KE

Brand: Canon Pages: 114

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 138

Brand: Canon Pages: 2

Brand: Canon Pages: 35

Brand: Canon Pages: 2

Brand: Canon Pages: 26

SECURICAM Network DCS-900

Brand: D-Link Pages: 20

SECURICAM Network DCS-2120

Brand: D-Link Pages: 25

DCS-6620G - Network Camera

Brand: D-Link Pages: 16

Brand: D-Link Pages: 7

Brand: D-Link Pages: 24

WIRELESS G DCS-950G

Brand: D-Link Pages: 2

Brand: Samsung Pages: 44

Brand: Olympus Pages: 156

Brand: Olympus Pages: 156

Brand: Olympus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands