Panasonic AJD440 - DVCPRO PLAYER Service Manual Download

Page: 88 / 104

3-13

1-16. Thrust Screw Replacement

and Adjustment

1. Remove the Thrust Adjustment Screw.
2. Enforce cleaning of point department of capstan

shaft with an applicator.

3. Put the oil (VFK0906) on a new Thrust

Adjustment Screw and install the upper end of the
Capstan Housing.

4. Turn the Thrust Adjustment Screw slowly to

counter-clockwise until the Capstan Rotor just
starts turning (separate from the Capstan Rotor).

5. Turn the Trust Adjustment Screw an another

angle of 270 degrees from 180 degrees (about
225 degrees) clockwise as shown in Figure 1-16-
2.

6. Put the glue (Ex. : Three Bond 1401B) on the

Thrust Adjust Screw.

7. Confirm whether the Oil Seal does not come in

contact with the Capstan Housing.

Figure 1-16-1

Figure 1-16-2

1-17. S5 Post Base Unit

Replacement

(Removal)
1. Unscrew the screw (A) and remove the S5 Post

Base Unit as shown in Figure 1-17.

(Installation)
1. Install the S5 post Base Unit follow the removal

steps in reverse order.

Note: Be careful the S5 Post Base Unit is install to

mech. chassis as shown in Figure 1-17.

2. After installation, Post Height Pre-Adjustment

and Tape pass Adjustment should be performed.

Figure 1-17

Thrust Adjustment Screw

Oil

180

225

270

Thrust Adjustment Screw

Capstan Housing

Oil Seal

Summary of Contents for AJD440 - DVCPRO PLAYER









































































































Search results

Summary of Contents for AJD440 - DVCPRO PLAYER

Reviews:

Related manuals for AJD440 - DVCPRO PLAYER

Brands by name

Popular brands

Panasonic AJD440 - DVCPRO PLAYER, Service Manual

Search results

Summary of Contents for AJD440 - DVCPRO PLAYER

Reviews:

Related manuals for AJD440 - DVCPRO PLAYER

Brands by name

Popular brands