manualshive.com logo in svg

Panasonic AJD440 - DVCPRO PLAYER, Service Manual

Share
Download
Panasonic AJD440 - DVCPRO PLAYER Service Manual Download Page 101

3-26

(Adjustment)
1. Place the reels in the L size position.
2. Push the iron core of M-Stopper Solenoid by

hand.

3. Observe the clearance (A) between Mech.

Chassis and M-Stopper as shown in Figure 1-31-
2. And make sure that it is within 1.1 to 1.3mm.

4. If not, loosen the 2 screws (A), which fixed M-

Stopper Solenoid. And adjust the position of M-
Stopper Solenoid so that the clearance (A) is
within specification. And tighten the 2 screws (A).

Figure 1-30-2

1-31. T4 Post Position Adjustment

1. Confirm that the hole (B) of T4 connection Gear

was matched to hole of T4 post as shown in
figure 1-31.

2. Confirm that the portion (C) of T4 connection

Gear and hole (A) , which are located as shown
in figure 1-31.

3. If not, adjust the phase of T4 post follow the

above procedure.

Note:
This confirmation should be performed on unloading
condition.

Figure 1-31

Summary of Contents for AJD440 - DVCPRO PLAYER









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands