Panasonic AJD440 - DVCPRO PLAYER Service Manual Download | Manualshive

Page: 71 / 104

background image

2-54

3-34. Self-REC/PLAY Envelope Waveform Confirmation

All of the head output are within specification as shown below.
Confirm in the 50M mode when your VTR or Camera Recorder is 50M model.

⋅

When using the M Cassette (66 min.) or L Cassette (126 min.)

SPEC.

V1/Vmax, V3/Vmax

≥

0.7

V2/Vmax

≥

0.8

⋅

When using the Long Time L Cassette (correspondence model only)

V1/Vmax, V2/Vmax, V3/Vmax

≥

0.7

V4/Vmax

≥

0.5

All R/P Envelope

: Refer to item “2. Table of Test Point”

TEST POINT

All PB Envelope (B type models only)

: Refer to item “2. Table of Test Point”

•

Confirm the all of the channels.

•

Confirm the PB envelope too about B type models.

M. EQ.

Oscilloscope

TAPE

•

M Cassette (66 min.) or L Cassette (126 min.)

•

Long Time L Cassette (correspondence model only)

TOOL

VFK1149 (Post Driver)

<Classified List>

Type

Models

A

AJ-D200, AJ-D210, AJ-D215, AJ-D400,
AJ-D610, AJ-D700, AJ-D700A, AJ-D780,
AJ-D800, AJ-D800A, AJ-D810, AJ-D810A,
AJ-D90, AJ-D900W, AJ-D900WA,
AJ-D910WA, AJ-PD900W, AJ-PD900WA,
AJ-DE77

B

AJ-D220, AJ-D230, AJ-D230H, AJ-D250,
AJ-D440, AJ-D450, AJ-D640, AJ-D650,
AJ-D750, AJ-D850, AJ-D92, AJ-D94,
AJ-D95DC, AJ-D940, AJ-D950, AJ-D950A,
AJ-LT75, AJ-LT85

1. Input the color bar signal and record it.
2. Playback the just recorded portion, and confirm

the envelope output is within specification.

3. If it is out of specification, perform the “ENV

Waveform Adjustment” and “LISTA Adjustment”
again.

NOTE 1 :
The model of AJ-D90, AJ-D900W, AJ-D900WA, AJ-
D910WA, AJ-PD900WA and AJ-PD900WA, which
models should be connect to BER COUNTER (refer
to item “Envelope Waveform Adjustment”).

NOTE 2 :
In case of AJ-D940, setting on Service Menu required.
(refer to item 3-11.)

«
...
69
70
71
72
73
...
»

Summary of Contents for AJD440 - DVCPRO PLAYER









































































































Reviews:

No comments

Related manuals for AJD440 - DVCPRO PLAYER

Brand: Neolab Pages: 5

Brand: JXD Pages: 2

Brand: Kenwood Pages: 56

Brand: Kenwood Pages: 56

Brand: Kenwood Pages: 56

Brand: Kenwood Pages: 40

Brand: Kenwood Pages: 48

Brand: Kenwood Pages: 40

Brand: Philips Pages: 3

Brand: Philips Pages: 29

Brand: Vjoy Car Pages: 2

Brand: Novus Pages: 52

Brand: Zaxcom Pages: 54

OBSERVER 4112 HVR

Brand: Safety Vision Pages: 15

Brand: Tascam Pages: 112

Brand: Samsung Pages: 111

Brand: Samsung Pages: 80

Brand: Samsung Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands