background image

MAJOR MECHANICAL PARTS REPLACEMENT

& ADJUSTMENT PROCEDURES

CONTENTS

1.

Major Mechanical Parts Replacement & Adjustment Procedures............................................. 3-1
GENERAL ..................................................................................................................................... 3-1
1-1. Cylinder Unit Replacement ................................................................................................... 3-1
1-2. Cleaning Arm Unit Replacement........................................................................................... 3-2
1-3. T1 Guide Position Adjustment............................................................................................... 3-2
1-4. Adjustment Flow Chart after Cylinder Unit Replacement ....................................................... 3-3
1-5. Supply & Take-up Reel Rotor Unit Replacement (except Camera Recorder) ......................... 3-4
1-5. Supply & Take-up Reel Rotor Unit Replacement (Camera Recorder only) ............................. 3-5
1-6. Main Brake Torque Confirmation........................................................................................... 3-6
1-7. Supply & Take-up Brake Arm Unit Replacement (except Camera Recorder) ......................... 3-6
1-8. Supply Brake Solenoid Replacement and Adjustment (except Camera Recorder)................. 3-7
1-9. Take-up Brake Solenoid Replacement and Adjustment (except Camera Recorder) ............... 3-8
1-10. Pinch Solenoid Replacement................................................................................................ 3-9
1-11. Pinch Solenoid Position Adjustment...................................................................................... 3-9
1-12. Pinch Arm Unit Replacement.............................................................................................. 3-10
1-13. Loading Motor Replacement............................................................................................... 3-10
1-14. Mode SW Unit Replacement................................................................................................3-11
1-15. Main Cam Gear Replacement..............................................................................................3-11
1-16. Thrust Screw Replacement and Adjustment........................................................................ 3-12
1-17. S5 Post Base Unit Replacement......................................................................................... 3-12
1-18. Tension Arm Unit Replacement........................................................................................... 3-13
1-19. S1 Post Loading Arm Unit Replacement and Adjustment .................................................... 3-14
1-20. T1 Boat Unit Replacement.................................................................................................. 3-15
1-21. T1 Loading Arm Unit Replacement and Adjustment ............................................................ 3-17
1-22. M-Cassette Brake Base Unit Replacement (Camera Recorder only) ................................... 3-17
1-23. A/C Head Replacement and Adjustment............................................................................. 3-18
1-24. Cleaner Solenoid Replacement and Adjustment ................................................................. 3-20

1-24-1. Cleaner Solenoid Position Adjustment .................................................................... 3-20
1-24-2. Cleaner Position Adjustment................................................................................... 3-21

1-25. Distinction SW Unit Replacement (except Camera Recorder) ............................................. 3-21
1-26. MIC Base Unit Replacement (Camera Recorder only) ........................................................ 3-22
1-27. Reel Drive Motor Unit Replacement (except Camera Recorder).......................................... 3-22
1-28. L-M Release Angle Unit Replacement (except Camera Recorder) ...................................... 3-22
1-29. Slide Rod Unit Replacement and Adjustment (except Camera Recorder)............................ 3-23
1-30. M-Stopper Solenoid Replacement and Adjustment (except Camera Recorder) ................... 3-24
1-31. T4 Post Position Adjustment............................................................................................... 3-25

2.

Connector Location................................................................................................................... 3-26
2-1. Mech. I/F P.C.Board (Type A Model) ................................................................................... 3-26
2-2. SERVO P.C.Board (Type B Model) ..................................................................................... 3-26
2-3. SERVO P.C.Board (Type C,D Model).................................................................................. 3-27

Summary of Contents for AJD440 - DVCPRO PLAYER









































































































Reviews: