Panasonic AJ-PX230 Series, Operating Instructions Manual

Page: 157 / 169

– 157 –
Chapter 9 Maintenance — Warning system
Display Description Behavior and cause
[REC IMPOSSIBLE] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
Recording to the SDHC/SDXC memory card is
disabled.
f
The current operation will continue.
f
Record to the microP2 memory card.
[REC WARNING]
[FRAME SIGNAL]
Displayed when a video or audio error occurs during
recording.
f
Tally lamp flashes four times per second during
continuous recording.
f
The current operation will continue. When input
signals are disrupted, recording continues while
disrupted images are recorded. Check the signal to
be input to the camera.
f
Turn off the power and on before using it again.
[REC WARNING]
[OVER MAX# CLIPS]
Displayed when attempting to record exceeding the
maximum limit for the number of clips allowed on a
single microP2 memory card.
f
Tally lamp flashes four times per second during
continuous recording.
f
The operation will stop.
f
Replace the microP2 memory card or delete the
unnecessary clips.
Displayed after approximately 3.5 hours have elapsed
from the time when operation to start a single recording
is executed, when [SHORT SPLIT] is selected in the
main menu → [RECORDING SETUP] → [FILE SPLIT].
f
The operation will stop.
[REC WARNING]
[PULL DOWN]
(Occurs during recording)
The video pull-down sequence and time code values
are not synchronized.
f
Tally lamp flashes four times per second during
continuous recording.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[PULL DOWN ERROR]
(Occurs at times other than during recording)
The video pull-down sequence and time code values
are not synchronized.
f
The current operation will continue.
f
Check the signal.
[REC WARNING]
[REC DATA]
Displayed when an error occurs in recorded data during
recording.
f
Tally lamp flashes four times per second during
continuous recording.
f
The operation will continue or stop.
f
Turn off the power and on before using it again.
[RUN DOWN CARD] (slot number)
The maximum number of overwrites has been
exceeded.
f
The current operation will continue.
f
It is recommended to replace the microP2 memory
card.
[SD CARD] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
f
The current operation will continue.
f
It is recommended to recording on the microP2
memory card.
[TEMPORARY PAUSE]
[IRREGULAR SIG]
The recording is paused because the recording cannot
be performed correctly due to disruption of the internal
standard signal. The clip will be divided.
f
Tally lamp flashes four times per second during
continuous recording.
f
The operation will pause.
f
Recording resumes when the signal returns to
normal. However, during loop recording, recording
does not resume.
[VFR ON, NO AUDIO RECORDING]
Native variable frame rate recording is performed.
Audio can not be recorded.
f
The current operation will continue.
During thumbnail and menu operation
Display Description Behavior and cause
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT ACCESS!]
Data cannot be accessed due to a content defect or
some other reason.
Ensure the health of the media and the clips.
[CANNOT CHANGE!]
For a clip with the mark, where a thumbnail cannot
be generated, the thumbnail cannot be modified in the
text memo position.
Correct the settings and content to enable display of the
thumbnail.
[CANNOT DELETE!] The content versions do not match. Cannot delete. Match the device and contents version.
[CANNOT FORMAT!]
Formatting is not possible due to problem in the
microP2 memory card, etc.
Check the microP2 memory card.
[CANNOT RE-CONNECT!]
The clips cannot be remerged because the contents
that are not recorded across multiple microP2 memory
cards are selected, etc.
Check the selected content.
[CANNOT REPAIR IN SELECTION!] Some of the selected clips cannot be repaired. Check the selected content.
[CANNOT REPAIR!] Content that cannot be repaired is selected. Check the selected content.
[CANNOT SAVE!]
[FILE NAME IN USE]
A settings file of the same name exists on the SD
memory card.
Use another name to save the file.
[CARD FULL!]
The microP2 memory card or the SD memory card is
full.
Insert a card with free space available.
[COPY IMPOSSIBLE. TOO LARGE CLIP
CONTAINED!]
[CLIP NAME:] (clip name)
The file exceeding 4 GB cannot be copied to a microP2
memory card 32 GB or less.
Copy to a microP2 memory card with 32 GB or larger
capacity.
[INVALID VALUE!] The data value you entered is invalid. Enter data within the normal range.
[INVALID DELETE]
The clip recorded last cannot be deleted with the last
clip delete function.
To close the dialog, press the [SET] button.
For details on conditions that clip cannot be deleted,
refer to “Deleting last clip function” (page 78).